LED indicator meanings

	LED indicator meanings

LED indicator	State	Meaning

STANDBY/ON (*)	Unlit	Electrical fault.
	Lit red	Standby

	Blinking green	Preparing for operation.

	Lit green	Operating

	Blinking red	Cooling the lamp.

	Blinking red / blinking	Blinking red: Error in the LAMP/COVER/TEMP system
	red rapidly	Blinking red rapidly: Error in the FAN system

LAMP	Unlit	Normal
	Blinking red	The lamp running time has exceeded 2000 hours.

	Lit red	The lamp has burned out.

COVER	Unlit	Normal
	Lit red	The lamp cover or the filter cover is not attached correctly.

TEMP	Unlit	Normal
	Lit red	The temperature of the lamp or the interior of the case is abnormally high.

FAN	Unlit	Normal
	Lit red	The cooling fan has broken.

(*) This LED is also present on the front panel of the main unit.

Reference

English

Page 67

Image 67

Yamaha DPX-1300 manual LED indicator meanings, LED indicator State Meaning

Contents

DPX-1300 Important Safety Instructions FCC Information for US customers only We Want You Listening For a Lifetime Iii Table of contents Accessory check Inappropriate places for installation Features English Features Main unit Front panel and controls Controls and functions Main unit Rear panel / Connections Remote control functions Remote control cable jack Remote control EnglishLight switch Remote control code switch Using the remote control with a wired connection Loading the batteries into the remote control Distance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screen Prepararion Turn the power on and selecting an image for projection Mounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling Projection distance InstallationWhen using a 169 screen When using a 43 screen Using the adjusters to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using V.POS vertical position to adjust image position Connection Connecting to AV components + polarity inside Polarity outside GND Connecting to computer devicesInformation for installers For US model only Projection preparations complete Checking installation and connectionsPre-operation check Projection English Turning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected image Crosshatch pattern Grayscale pattern Color bar pattern Adjusting the imageAdjusting the vertical position V.POS button Pattern button Adjusting the size of an image Zoom button Menu screen Menu configurations Menu item list Menu items Lower level menu items Submenu Items Menu group items and functions Menu White Peaking Level AdjustmentAdjusts the iris Optical Adjusts the analog input signal gain and offset settings Menu English Signal Overshoot Supp. Level Signal LevelSignal Status Overshoot Supp. Range Initial Setup Baud Rate Menu ColorMessage Trigger Out Operation button functions Reset button Remote control onlyRemote Control Menu operations Press the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu screen Remote Control Main Unit Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main Unit Menu Button Appears to the right of items that contain a submenu Press the h or g button to adjust item settingsMenu operations 2 with submenus Press the + button to move to the submenu See page 32 for datails about each color item Special operations Example Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Subtitle Zoom Resetting the lamp running time Press the button Changing the Gamma Inline menu item list Adjusting image quality using the inline menuExample Using the inline menu Inline menu composition Using the menu Memory configurationsSaving memory settings Using the remote control Press the h or g button to select a memory number Memory function EnglishPress the g button to select Memory number status from Bottom of the screen Select the memory number you Setting Memory LockMemory lock Deactivating Memory Lock Press the g button to select Memory copyRecall the memory number to be Copy source Press the + button to display the confirmation screen Initialization of the currently selected memory Resetting to the default settings in the memory menu Initialization of all the memories Reference Glossary Compatible signal types Reference English Signal type Active Component type Pixels Lines KHz Regular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws To protect the lamp, you cannot turn on Troubleshooting Troubleshooting Message Condition Message display LED indicator State Meaning LED indicator meanings General SpecificationsOptical Controls 119.1 Dimensional drawing C2005 All Rights Reserved

LED indicator

State

Meaning

STANDBY/ON (*)

LAMP

TEMP

FAN

Reference