Yamaha DPX-1300 Connecting to computer devices

16

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and

jacks you wish to use. The HDMI terminal does not support PC signals.

Connecting to computer devices

HDMIDVI

G/Y B/P

B

/C

B

R/P

R

/C

R

INPUT A

HD/SYNC VD

OUT IN

REMOTE TRIGGER OUT

S VIDEO VIDEO

INPUT B

RGB/YP

B

P

R

/YC

B

C

R

RS-232C

D4 VIDEO

D-Sub monitor

cable

BNC monitor cable

Monitor output terminal

Computer devices

Use the supplied trigger-out DC plug to control external

components.

Be sure to solder the wires from an external component to the

plug terminals with the correct polarities, as illustrated at left.

Warning

•Soldering the wires to terminals with incorrect polarity may

cause bodily injury or may damage this unit and the

external component connected to this unit with this cable.

Information for installers

(for US model only)

+ polarity (inside)

- polarity (outside)

(GND)

+ polarity

- polarity

Input

INPUT A

INPUT B

DVI

Signal type

RGB (Analog)

RGB (Analog)

RGB (Digital)

Connector type

BNC jack x 5

D-sub 15 pin

DVI connector

DVI cable

11_DPX-1300_E.p65 9/20/05, 4:00 PM16

Contents

Main DPX-1300 Printed in Japan WF80490 10_DPX-1300-Cover1-4_U.p65 9/22/05, 4:28 PM1 DIGITAL CINEMA PROJECTOR PROJECTEUR CINEMA NUMERIQUE DPX-1300 IMPORTANT! IMPORTANT SAFETY INSTRUCTIONS i We Want You Listening For A Lifetime COMPLIANCE INFORMATION STATEMENT ii English Caution: Read this before operating this unit. Installation Operation Others For U.K. customers Table of contents Inappropriate places for installation 1. Places where the temperature and humidity vary greatly 2. Places without adequate ventilation 3. Places where it gets dusty 1Getting started Features 2Features Main unit <Front panel and controls> 3Controls and functions Controls and functions 3 ert wq 8 765432190 Main unit <Rear panel / Connections> 4Remote control Remote control 7 iINPUT button oLIGHT switch pHIDE button Loading the batteries into the remote control 11_DPX-1300_E.p65 9/20/05, 4:00 PM8 DVI INPUT MENU 4 11_DPX-1300_E.p65 9/20/05, 4:00 PM9 Use within a left/right arc of 30 degrees Use within a vertical arc of 30 degrees Distance to sensor Angle to sensor 7 m 30 vertically and horizontally (approximate value) (approximate value) STEP2 5 STEP 1 STEP2 Preparation Prepararion Step2 Connect an AV component or computer Turn the power on and selecting an image for projection Step1 Set up the projector and screen Setting up the DPX-1300 6 Mounting the projector on a table A: From in front of a screen B: From behind a screen (using a semi-translucent screen) Projection distance <When using a 4:3 screen> <When using a 16:9 screen> 14 <Using ZOOM to adjust image position> Projection image position Keystone adjustment Connection Connecting to AV components 7Connection 16 - Connecting to computer devices Information for installers (for US model only) + - + 17 Checking installation and connections Projection preparations complete Pre-operation check Check installation and connections Select an image for projection and image adjustment Turn on the projector power. Turning the projector power on 1. Press the STANDBY/ON button. A confirmation message appears on the screen. Placing the DPX-1300 in standby mode Turning the projector power on Selecting using the INPUT button Projection image signal INPUT SIGNAL Selecting an input signal 21 <Using the INPUT button to select a signal> + button 1. Press the INPUT button. The input signal selection menu appears on the display. 2. Use the h or g buttons to select an input signal, then press the button. Selecting a display aspect for a projection image button cursor button Remote cotrol Main unit ASPECT 23 <Display aspect types> Auto Normal Squeeze 24 <Representative examples> Adjusting the vertical position V.POS button Using test patterns to adjust the projection image PATT button Adjusting the image Adjusting the image Adjusting the size of an image ZOOM button Adjusting the image focus FOCUS button Adjusting the iris setting IRIS button Menu configurations Menu screen 9Menu Menu item list: Image Menu items 29 <Submenu Items> Signal Setup <Lower level menu items> Menu group items and functions <Image> Black Level Contrast Gamma 31 Hue Color Adjustment Sharpness Gain Sharpness Type 32 Iris Level Adjustment White Peaking Color Adjustment (continued) Signal Display Aspect Ratio Overscan 3D Y/C Separation Progressive Mode 34 Overshoot Supp. Range Noise Reduction Type Horiz. Display Position Vert. Display Position Initial 36 Setup Location V Keystone Correction Remote Control Sensor Remote Control ID 37 Menu Color Trigger Out Sets the TRIGGER OUT terminal. Baud Rate Message Menu operations Operation button functions 1Menu Button 2Cursor button 3 button Menu operations 1 (with no submenu) 14_DPX-1300_E.p65 9/23/05, 12:03 PM39 Remote Control Main Unit or Remote Control Main Unit 6. To close the menu screen when you have finished making adjustments, press the MENU button. 5. Move to another item or group as necessary. 14_DPX-1300_E.p65 9/20/05, 4:01 PM40 The setting method depends on the item selected. ESCAPE Button Menu operations 2 (with submenus) 42 <Color Adjustment> Special operations Page 44 <Resetting the selected settings> <Resetting all the settings> <Changing the position of the menu screen.> 45 <Resetting the lamp running time> <Subtitle Zoom> 46 14_DPX-1300_E.p65 9/20/05, 4:01 PM46 Press the button Press the h or g button to move to a different menu item in the [Subtitle Zoom] menu. 8. Press the ESCAPE button to return to the higher level selection menu. Adjusting image quality using the inline menu For PC type sources Gamma A B CDE <Inline menu composition> Black Level 10 Memory function (Save, Recall, Lock, Copy, Reset) Input The Number of Memories 2. Press the g button to select Memory number status from the bottom of the screen. Memory number status 15_DPX-1300-E.p65 9/20/05, 4:01 PM49 5. Press the button to recall the settings in the selected memory. 4. Press the h or g button to select a memory number. Memory lock 15_DPX-1300-E.p65 9/22/05, 6:19 PM50 disappears or Remote Control Main Unit Memory copy 15_DPX-1300-E.p65 9/20/05, 4:01 PM51 Copy the settings stored in a memory number to another memory number. 2. Press the g button to select Memory number status from the bottom of the screen. Memory number status Page 53 Resetting to the default settings in the memory menu <Initialization of the currently selected memory> 54 <Initialization of all the memories> Glossary 11 Reference Compatible signal types Sync. Test pattern Tracking Vista size DVI Format PC Format (Analog RGB PC signals received at the INPUT A or B jack) HDMI Format (Component/RGB signals input from the HDMI jack) Compatible signal types 58 Maintenance Replacing the lamp Maintenance Troubleshooting Troubleshooting Troubleshooting Message display LED indicator meanings Specifications Controls General Input Optical Dimensional drawing DPX-1300 Printed in Japan WF80490-1 10_DPX-1300-Cover1-4_U.p65 12/7/05, 4:45 PM1 C2005 All Rights Reserved. DIGITAL CINEMA PROJECTOR PROJECTEUR CINEMA NUMERIQUE DPX-1300