Turning the projector power on | Yamaha DPX-1300 specification

Turning the projector power on

◆Turning the power on

Always remove the lens cap before operating the main unit.

	STANDBY/ON
	STANDBY/ON
	indicator
ESCAPE	MENU
PATTERN	SETTING
ASPECT	INPUT
	LAMP COVER TEMP FAN

1.Insert the supplied power cable firmly into the AC inlet at the rear of the main unit, then insert the plug into an AC outlet.

The STANDBY/ON indicator lights red.

		AC inlet
		button STANDBY/ON button
AUTO
			STANDBY/ON
V. POS	ZOOM	FOCUS
IRIS	SETTING	PATT
		ESCAPE	MENU
ESCAPE		MENU
		PATTERN	SETTING
		ASPECT	INPUT
ASPECT		INPUT	LAMP COVER TEMP FAN
ASPECT		INPUT
Remote Control			Main unit

2.Press the STANDBY/ON button

(the button on the remote control).

The indicator blinks green and the lamp lights up in preparation for projection. After approximately 35 seconds, the indicator changes from blinking to steady green, indicating that the unit is ready to project.

Warning

•Do not remove the power cable while the STANDBY/ON indicator is blinking green or lit steady green. This could damage the lamp or reduce lamp life.

18

Image 22

Yamaha DPX-1300 manual Turning the projector power on, Turning the power on

Contents

DPX-1300 Important Safety Instructions We Want You Listening For a Lifetime FCC Information for US customers only Iii Table of contents Inappropriate places for installation Accessory check Features Features English Main unit Front panel and controls Main unit Rear panel / Connections Controls and functions Remote control functions Remote control code switch Remote control EnglishLight switch Remote control cable jack Loading the batteries into the remote control Using the remote control with a wired connection Distance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen Preparation Turn the power on and selecting an image for projection Prepararion Mounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling When using a 43 screen InstallationWhen using a 169 screen Projection distance Using V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image position Connecting to AV components Connection For US model only Connecting to computer devicesInformation for installers + polarity inside Polarity outside GND Projection English Checking installation and connectionsPre-operation check Projection preparations complete Turning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Input signal typeInput imageDisplay aspectProjected image Representative examples Pattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar pattern Adjusting the size of an image Zoom button Menu configurations Menu screen Menu items Menu item list Submenu Items Lower level menu items Menu group items and functions Menu Adjusts the analog input signal gain and offset settings Level AdjustmentAdjusts the iris Optical White Peaking Signal Menu English Overshoot Supp. Range Signal LevelSignal Status Overshoot Supp. Level Initial Setup Trigger Out Menu ColorMessage Baud Rate Menu operations Reset button Remote control onlyRemote Control Operation button functions Menu screen Menu operations 1 with no submenuPress the Menu button to open Press the + or button to select a menu group Remote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main Unit Press the + button to move to the submenu Press the h or g button to adjust item settingsMenu operations 2 with submenus Appears to the right of items that contain a submenu Special operations See page 32 for datails about each color item Example Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Resetting the lamp running time Subtitle Zoom Changing the Gamma Press the button Inline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item list Using the remote control Memory configurationsSaving memory settings Using the menu Bottom of the screen Memory function EnglishPress the g button to select Memory number status from Press the h or g button to select a memory number Deactivating Memory Lock Setting Memory LockMemory lock Select the memory number you Copy source Memory copyRecall the memory number to be Press the g button to select Press the + button to display the confirmation screen Resetting to the default settings in the memory menu Initialization of the currently selected memory Initialization of all the memories Glossary Reference Compatible signal types Signal type Active Component type Pixels Lines KHz Reference English Regular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn on Troubleshooting Message display Message Condition LED indicator meanings LED indicator State Meaning Controls SpecificationsOptical General Dimensional drawing 119.1 C2005 All Rights Reserved