Yamaha DSP-AX1 ■ Connecting a Turntable, ■ Connecting a CD Player, ■ Connecting an AM/FM Tuner

Preparations

Hookups

Connecting Audio Components

Before you connect any components, disconnect the power supply to all the components you plan to connect including the DSP-AX1 and determine which jacks are for the left and right channels and for input and output.

When you connect other YAMAHA audio equipment (such as a CD player or changer, Tuner, MD deck, or tape deck), connect to terminals with the same number labels. Yamaha applies this labelling system to all its products.

In the hookup illustrations on the following pages:

indicates signal direction,

C indicates coaxial cables,

L indicates left side analog cables,

R indicates right side analog cables,

Oindicates optical cables; and,

Sindicates S-video cables.

After you finish all hookups, check them again to make sure they are correct.

AM/FM Tuner	L	Audio Output
	R	■ Connecting an AM/FM Tuner

1Connect the left and right signal output jacks on your tuner

RF(AC-3)	GND	AUDIO	AUDIO		VIDEO	COMPONENT VIDEO				to the TUNER 2 L and R jacks.
		PHONO			VIDEO S VIDEO	Y	PB/CB	PR/
LD					DVD	A
CD	CD				LD	B
DVD	TUNER				D-TV	C
CBL	IN				CBL
/SAT	(PLAY)				/SAT			M
COAXIAL	TAPE
OPTICAL
	OUT				IN		PREOUT/MAIN
CD
	(REC)
										■ Connecting a Turntable
Turntable		Output			L					1 Connect the left and right signal output cords to the PHONO L and
		Ground			R
										R jacks.
										Note:
										• These jacks are for connecting a turntable with an MM or high output MC
	RF(AC-3)			AUDIO	AUDIO		VIDEO			cartridge. If you have a turntable with a low output MC cartridge, use an inline
		GND		PHONO		VIDEO	S VIDEO			boosting transformer or MC-head amplifier when connecting to these jacks.
		LD				DVD
		CD	CD			LD				Caution:
		DVD	TUNER			D-TV				• The GND terminal does not electrically ground the turntable. It simply reduces
		CBL	IN			CBL
		/SAT	(PLAY)			/SAT				noise in the signal. In some cases, you may hear less noise if you do not connect to
										the GND terminal.
Optical Output						Analog				■ Connecting a CD Player
						Output
			CD Player					L
								R
										1 Connect the left and right analog signal output jacks on your CD
Coaxial Output
C										player to the CD 1 L and R jacks.
		RF(AC-3)		GND	AUDIO	AUDIO		VIDEO	COMPONEN
					PHONO		VIDEO	S VIDEO	Y	Notes:
			LD				DVD		A
O			CD	CD			LD		B	• The COAXIAL CD and OPTICAL CD jacks are available for a CD player which
			DVD	TUNER			D-TV		C	has coaxial or optical digital outputs.
		COAXIAL		TAPE			CBL			• When you connect a CD player to both the COAXIAL CD and OPTICAL CD
			CBL	IN
			/SAT	(PLAY)			/SAT
		OPTICAL	CD	(REC)						jacks, priority is given to the input signals from the COAXIAL CD jack.
							IN
				OUT
							VCR 1			• The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber
				MD
			IN	IN			OUT
			(PLAY)	(PLAY)
			MD	(REC)					IN	optic cable that does not conform to this standard, the DSP-AX1 may not function
			(REC)				IN		REMOTE 1
			OUT	OUT
							VCR 2		OUT	properly.
			DVD
				MAIN			OUT

16