Yamaha DSP-AX563 54 En, Speaker distance CSP Distance, Center speaker equalizer Dcenter GEQ

SET MENU

■Speaker distance C)SP DISTANCE

Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time.

1 SOUND MENU	1 SOUND MENU
C)SP DISTANCE 1/2	C)SP DISTANCE 2/2
. UNIT;;;;;;meters	. SUR. L;;;;;3.00m
FRONT L;;;;3.00m	SUR. R;;;;;3.00m
FRONT R;;;;3.00m
CENTER;;;;;2.60m
SWFR;;;;;;;3.00m
[p]/[p]:Up/Down	[p]/[p]:Up/Down
[p]/[[]:Adjust	[p]/[[]:Adjust

Unit UNIT

Choices: meters (m), feet (ft)

Initial setting: meters (m)

•Select “meters” to adjust speaker distances in meters.

•Select “feet” to adjust speaker distances in feet.

Speaker distances

Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)

Control step: 0.10 m (0.5 ft) Initial setting:

FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)

CENTER: 2.60 m (8.5 ft)

SUR. L/SUR. R/SB L/SB R: 2.40 m (8.0 ft)

SP DISTANCE	Adjusted speaker
FRONT L	Front left speaker
FRONT R	Front right speaker
CENTER	Center speaker
SWFR	Subwoofer
SUR. L	Surround left speaker
SUR. R	Surround right speaker
SB L	Surround back left speaker
SB R	Surround back right speaker

Notes

•The available speaker channels differ depending on the setting of the speakers.

•Instead of “SB L” and “SB R”, “SUR.B” is displayed if “SUR.B L/R SP” is set to either “SMLx1” or “LRGx1” (see page 52).

■Center speaker equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band (100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic equalizer for the center channel so that the tonal quality of the center speaker matches that of the front speakers. You can make adjustments while listening to the currently selected source component or a test tone.

Control range: –6.0 to +6.0 dB

Control step: 0.5 dB

Initial setting: 0 dB

1 SOUND MENU
D)CENTER GEQ
TEST	>OFF	ON
. 100Hz	;;;;;;	0dB
300Hz	;;;;;;	0dB
1kHz	;;;;;;	0dB
3kHz	;;;;;;	0dB
10kHz	;;;;;;	0dB

[p]/[p]:Up/Down [p]/[[]:Adjust

Test tone TEST

Use this feature to make adjustments for “CENTER GEQ” while listening to a test tone.

Choices: OFF, ON

•Select “OFF” to stop test tones and output the currently selected source component.

•Select “ON” to output test tones from the center and front left speakers.

■Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (low- frequency effect) channel according to the capacity of your subwoofer or headphones. The LFE channel carries low-frequency special effects which are only added to certain scenes. This setting is effective when the input signal contains the LFE channel.

Control range: –20 to 0 dB

Control step: 1 dB

1 SOUND MENU

E)LFE LEVEL

.SPEAKER;;;;;;0dB HEADPHONE;;;;0dB

[p]/[p]:Up/Down [p]/[[]:Adjust

Speaker SPEAKER

Adjusts the speaker LFE level.

Headphone HEADPHONE

Adjusts the headphone LFE level.

Note

Depending on the settings of “LFE/BASS OUT” (see page 52), some signals may not be output at the SUBWOOFER OUTPUT jack.

54 En