REMOTE CONTROL FEATURES

Setting the Manufacturer Code

You can control other components by setting a manufacturer code. A code can be set up in each input area.

The following table shows factory-set component (Library: component category) and the manufacturer code for each area. If you are to make a setting for different component from the factory setting, change the library as described in step 3 on right.

Input area

Component category

Manufacturer

 

(Library)

 

 

 

 

A

LD

Yamaha

 

 

 

B

SAT

–

 

 

 

PHONO

TV

–

 

 

 

V-AUX

VCR

–

 

 

 

TUNER

TUNER

Yamaha-1

 

 

 

MD/TAPE

MD

Yamaha-1

 

 

 

CD-R

CD-R

Yamaha

 

 

 

D-TV/LD

TV

–

 

 

 

VCR 1

VCR

–

 

 

 

VCR 2/DVR

VCR

–

 

 

 

DVD

DVD

Yamaha-1

 

 

 

CD

CD

Yamaha-1

 

 

 

CBL/SAT

CABLE

–

 

 

 

Note

•You may not be able to operate your Yamaha component even if Yamaha manufacture code is initially set as listed above. In this case, try to set other Yamaha manufacture code(s).

1 Press an input selector button, Å or ı to select the source component you want to set up.

 

 

A

B

PHONO

V-AUX

TUNER

MD/TAPE

CD-R

CD

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

DVD

2 Press and hold LEARN for about 3 seconds by using a ballpoint pen or similar object.

“SETUP” and the selected component name appear alternately in the display window.

LEARN

Notes

•Press LEARN for at least 3 seconds, otherwise the learning process is started.

•Complete each of the following steps in 30 seconds. Otherwise, the learning mode will be automatically canceled. In this case, press LEARN again.

3 Press k / n to select the name of your component’s manufacturer.

You will find the names of most worldwide audio- video manufacturers in alphabetical order in the display window.

ENTER

If you want to change a library (component category), press l / h. You can set a different component from the input selector name.

Library choices: L:DVD, L:LD, L:CD, L:CDR, L:MD, L:TAP, L:TUN, L:AMP*, L:TV, L:CAB, L:DBS, L:SAT, L:VCR

■Amplifier Library (L:AMP)

The code to operate this unit has been preset in the supplied remote control. However you can change the code in Amplifier Library if necessary.

Amplifier Library has the following four codes: YPC: Code to operate this unit.

Zone 2: Code to use the Zone 2 function. This code is not used with this unit.

DSP: Code to operate other Yamaha DSP amplifiers that cannot be operated with the YPC code.

NO: Code to operate other manufacturers’ amplifiers using this unit’s remote control.

4 Press one of the buttons shaded below to check if it works for the component being set. If it does, the manufacturer code setting has been correctly made.

 

 

 

 

6CH INPUT

 

 

TITLE

 

 

 

 

 

ENTER

 

SOURCE

 

 

 

 

 

DISPLAY

MENU

 

SOUND

SELECT

SEARCH

– CHAPTER +

POWER

REC

STOP

PAUSE

PLAY

Note

•If the manufacturer of your component has more than one codes, try each of them until you find the correct one.

y

•If you continuously want to set up another code for another component, press ENTER and repeat steps 1, 3 and 4.

42