SPEAKER BALANCE ADJUSTMENT

This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder.

The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. Otherwise, the result may not be satisfactory.

Note

If this unit is connected with a Dolby Digital (AC-3) Decoder and/or an amplifier (or receiver) equipped with the Dolby Pro Logic Decoder or the digital sound field processor, also make an output balance adjustment using the test tone on each unit.

2

 

 

 

 

 

 

 

 

 

1

–

TIME/

+

DELAY/CENTER

 

EFFECT

 

 

 

 

 

 

 

 

 

 

 

 

 

LEVEL

/REAR/SWFR

TEST

 

4, 8

 

 

 

 

 

 

 

 

 

 

 

 

7

PROGRAM

 

PROLOGIC

ENHANCED

ON/OFF

 

 

 

 

 

 

 

 

 

 

l6

 

 

 

VCR

 

TV/DBS DVD/LD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NATURAL SOUND

AV PROCESSOR/AMPLIFIER DSP–E492

CINEMA DSP

 

 

 

 

 

VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VCR

TV/DBS

DVD/LD

20

l2

DIR A DIR B

REC/PAUSE

PLAY

 

 

 

 

PRESET

 

 

ms dB STEREO

SLEEP

NORMAL

 

 

28

 

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

 

 

 

kHz

 

 

PHANTOM

 

 

40

 

4

 

 

 

 

A/B

 

TAPE

 

 

 

 

 

MHz

 

 

EFFECT OFF

 

 

 

 

 

 

 

 

 

 

MEMORY AUTO PTY HOLD

 

 

 

ROCK CONCERT

2CH/6CH

 

 

 

 

 

 

 

 

 

 

 

 

PS

INFO AFFAIRS SPORT TAPE MONITOR PRO LOGIC CONCERT MONO DISCO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PTY RT CT EON NEWS

 

ENHANCED VIDEO MOVIESTADIUMCONCERT HALL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAPE (MD)

TUNER

CD

60

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONITOR

(LINE 2)

(LINE 1)

 

 

–

 

+

 

 

 

TUNER L2

 

EFFECT

PRO LOGIC

ENHANCED CONCERT VIDEO

MONO MOVIE STADIUM

DISCO

ROCK CONCERT CONCERT HALL

 

 

 

0

PRESET

A/B/C/D/E

 

 

 

 

 

 

 

 

 

 

 

–dB

 

 

 

 

 

 

 

 

 

 

 

PROCESSOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SELECTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INTERNAL

 

 

 

DISC

PLAY

 

CD L1

 

 

 

 

 

 

 

 

CENTER

DELAY/

TIME/LEVEL

EXTERNAL

 

 

 

 

 

 

 

 

 

 

 

 

 

MODE

CENTER/REAR

 

 

 

 

 

 

 

 

 

 

 

2CH/6CH VOLUME

5

1

VOLUME

 

 

l6

20

l2

28

8

40

4

602

0

–dB

Set to the “∞ ” position.

2 Turn on the power of this unit and the external amplifier etc.

POWER

3 Set the balance control, tone controls, etc. on the external amplifier to the “flat” position.

4 TEST

6

5 Select the center channel output mode suitable for your speaker configuration.

(Refer to “SPEAKER CONFIGURATION” on page 7.)

CENTER

MODENORMAL

WIDE

PHANTOM

On the feature of each mode, refer to the “Note” shown below.

Note

In step 5, when you select a center channel output mode, note the following.

For 5-speaker configuration)

NORMAL: Select this mode when you use a center speaker that is smaller than the main speakers. In this mode, the bass tone will be output from the main speakers.

WIDE: Select this mode when you use the center speaker approximately same sized as the main speakers.

For 4-speaker configuration)

PHANTOM: Select this mode when you do not use the center speaker. The center sound will be output from the left and right main speakers.

18