Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha HTR-5860 Speaker connections, ■Connecting to PRESENCE speaker terminals, ■Banana plug connections, CAUTION, 1Open the tab, 3Unscrew the knob

1 103

Download 103 pages, 3.19 Mb

SPEAKER SETUP

Speaker connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.

CAUTION

•If you will use 4 or 6 ohm speakers, be sure to set this unit’s speaker impedance setting to 4 ohms before using (see page 22).

•Before connecting the speakers, make sure that the power of this unit is off.

•Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.

•Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red) terminals on this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

10 mm (3/8")

1 2

1Remove approximately 10 mm (3/8") of insulation from the end of each speaker cable.

2Twist the exposed wires of the cable together to prevent short circuits.

3Unscrew the knob.

4Insert one bare wire into the hole in the side of each terminal.

5Tighten the knob to secure the wire.

3

4

5

Red: positive (+)

Black: negative (–)

■Connecting to PRESENCE speaker terminals

2 1 3

1Open the tab.

2Insert one bare wire into the hole of each terminal.

3Return the tab to secure the wire.

■Banana plug connections

First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.

Banana plug

y

You can also use banana plugs with the PRESENCE speaker terminals. Open the tab, then insert one banana plug connector into the hole of each terminal. Do not attempt to close the tabs after connecting the banana plugs.

12

Contents

Page IMPORTANT SAFETY INSTRUCTIONS Note to CATV system installer: FCC INFORMATION (for US customers) 1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT NOTE: CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES Built-in 7-channelpower amplifier Sound field features Sophisticated AM/FM tuner XM Satellite Radio GETTING STARTED Supplied accessories Installing batteries in the remote control Notes on batteries CONTROLS AND FUNCTIONS Front panel BOPTIMIZER MIC jack CPHONES (SILENT CINEMA) jack DSPEAKERS A/B ESTRAIGHT (EFFECT) FPROGRAM Remote control Using the remote control ■Handling the remote control Front panel display Page Rear panel SPEAKER SETUP Speaker placement Surround speakers (SR and SL) Surround back speakers (SBR and SBL) Subwoofer Speaker connections ■Connecting to PRESENCE speaker terminals ■Banana plug connections Page ■FRONT terminals ■CENTER terminals ■SURROUND terminals ■SURROUND BACK terminals ■PRESENCE terminals CONNECTIONS ■Cable indications ■Analog jacks ■Digital jacks ■Video jacks Connecting video components ■Connections for DVD playback ■Connecting to the MULTI CH INPUT jacks ■Connections for other video components ■ VIDEO AUX jacks (on the front panel) Connecting audio components ■Connections for audio components ■Connecting to an external amplifier Connecting the FM and AM antennas ■Connecting the AM loop antenna ■Connecting the AC power cord ■AC OUTLET(S) (SWITCHED).....2 outlets ■Memory back-up Speaker impedance setting Turning on the power AUTO SETUP Introduction Optimizer microphone setup Starting the setup ■If an error screen appears ■If a warning screen appears ■Troubleshooting for auto setup procedure Warnings after auto setup Warning message PLAYBACK Basic operations ■To mute the sound ■To listen with headphones (“SILENT CINEMA”) ■To adjust the tone ■Selecting MULTI CH INPUT ■Front panel operation ■Remote control operation ■Enjoying multi-channelsoftware ■Enjoying 2-channelsoftware in surround ■Listening to high fidelity stereo sound (PURE DIRECT) ■Night listening modes ■Downmixing to 2 channels ■Listening to unprocessed input signals ■Virtual CINEMA DSP Selecting input modes ■Displaying information about the input source 3Press u / d to display the following information about the input signal FM/AM TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting FM stations ■Manually presetting stations Automatic preset tuning options: Selecting preset stations Exchanging preset stations Page XM SATELLITE RADIO TUNING What is XM Satellite Radio XM Satellite Radio connections ■Connecting the XM Connect and Play digital antenna accessory XM Satellite Radio functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations ■Selecting the XM Satellite Radio mode ■Switching XM information in the front panel display ■Displaying XM information in the on XM Satellite Radio search modes ■All Channel Search mode ■Category Search mode ■Preset Search mode ■Direct Number Access mode Setting XM Satellite Radio preset channels While the MEMORY indicator is flashing, press PRESET/TUNING/CH ■Status and error messages RECORDING ■Special considerations when recording DTS software SOUND FIELD PROGRAM DESCRIPTIONS For movie/video sources Page For music sources ADVANCED OPERATIONS Selecting the OSD mode Using the sleep timer ■Setting the sleep timer ■Canceling the sleep timer SET MENU ■AUTO SETUP ■MANUAL SETUP ■SIGNAL INFO Using SET MENU 1 SOUND MENU ■Speaker settings A)SPEAKER SET Surround back speakers SUR. B L/R SP SMLx2 Presence speakers PRESENCE SP NONE Bass out Speaker level ■Speaker distance C)SP DISTANCE ■Center graphic equalizer D)EQUALIZER ■Low-frequencyeffect level E)LFE LEVEL ■Audio settings G)AUDIO SET Dynamic range 2 INPUT MENU ■Input/output assignment ) and B ) and and Input mode Volume Trim Input rename 3 OPTION MENU ■Display settings A)DISPLAY SET Memory guard ■Parameter initialization C)PARAM. INI Zone set Speaker B setting SP B ■XM Radio setting E)XM RADIO SET ADVANCED SETUP MENU ■ADVANCED SETUP menu items REMOTE CONTROL FEATURES Control area ■Controlling this unit ■Controlling other components Setting remote control codes Controlling other components Switching library codes Clearing set up remote control codes EDITING SOUND FIELD PARAMETERS What is a sound field Changing parameter settings ■Elements of a sound field ■Resetting parameters to the factory presets SOUND FIELD PARAMETER DESCRIPTIONS ■DSP LEVEL (DSP level) ■INIT. DLY/P. INIT. DLY (Initial delay) ■ROOM SIZE/P. ROOM SIZE (Room size) ■LIVENESS (Liveness) ■S. INIT. DLY (Surround initial delay) ■S. ROOM SIZE (Surround room size) ■S. LIVENESS (Surround liveness) ■SB INI. DLY (Surround back initial delay) ■REV.TIME (Reverberation time) ■REV.DELAY (Reverberation delay) ■REV. LEVEL (Reverberation level) ■DIALG.LIFT (Dialog lift) For 2ch Stereo: ■DIRECT (Direct) For 7ch Stereo: ■CT LEVEL (Center level) For DTS Neo:6 Music: ■C. IMAGE (Center image) TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control RESETTING THE FACTORY PRESETS GLOSSARY Audio formats ■Dolby Digital ■Dolby Digital EX ■Dolby Pro Logic Sound field programs ■CINEMA DSP ■SILENT CINEMA Audio information ■ITU-R Video signal information ■Component video signal ■Composite video signal ■S-videosignal SPECIFICATIONS LIST OF REMOTE CONTROL CODES APPENDIX-i SATELLITE TUNER (DBS) VCR APPENDIX-ii CD PLAYER DVD PLAYER DVD RECORDER CD RECORDER APPENDIX-iii TAPE DECK APPENDIX-iv