Yamaha HTR-5860 91

TROUBLESHOOTING

	Problem	Cause	Remedy	Refer to
	Problem	Cause	Remedy	page
				page

	Dolby Digital or DTS	The connected component is not set to	Make an appropriate setting following the operating	—
	sources cannot be	output Dolby Digital or DTS digital	instructions for your component.
	played. (Dolby Digital	signals.
	or DTS indicator on
	or DTS indicator on	The input mode is set to ANALOG.	Set the input mode to AUTO or DTS.	36
	the front panel	The input mode is set to ANALOG.	Set the input mode to AUTO or DTS.	36
	display does not light
	up.)

	A “humming” sound	Incorrect cable connections.	Firmly connect the audio plugs. If the problem	—
	can be heard.		persists, the cables may be defective.

	The volume level	The component connected to the OUT	Turn on the power to the component.	—
	cannot be increased,	(REC) jacks of this unit is turned off.
	or the sound is
	distorted.

	The sound effect	It is not possible to record the sound effect
	cannot be recorded.	with a recording component.

	A source cannot be	The source component is not connected to	Connect the source component to the DIGITAL	15-19
	recorded by a digital	this unit’s DIGITAL INPUT jacks.	INPUT jacks.
	recording component
	recording component	Some components cannot record the
	connected to this	Some components cannot record the
	DIGITAL OUTPUT	Dolby Digital or DTS sources.
	jack.

	A source cannot be	The source component is not connected to	Connect the source component to the analog AUDIO	15-19
	recorded by an	this unit’s analog AUDIO IN jacks.	IN jacks.
	analog component
	connected to the
	AUDIO OUT jacks.

	The sound field	“MEMORY GUARD” in SET MENU is	Select OFF.	70
	parameters and some	set to ON.
	other settings on this
	unit cannot be
	changed.

	This unit does not	The internal microcomputer has been	Disconnect the AC power cord from the outlet and	—
	operate properly.	frozen by an external electric shock (such	then plug it in again after about 30 seconds.
		as lightning or excessive static electricity)
		or by a power supply with low voltage.

	“CHECK SP WIRES”	Speaker cables are short circuited.	Make sure all speaker cables are connected correctly.	12
	appears in the front
	panel display.

INFORMATION	ADDITIONAL

87

Contents

Page IMPORTANT SAFETY INSTRUCTIONS Note to CATV system installer: FCC INFORMATION (for US customers) 1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT NOTE: CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES Built-in 7-channelpower amplifier Sound field features Sophisticated AM/FM tuner XM Satellite Radio GETTING STARTED Supplied accessories Installing batteries in the remote control Notes on batteries CONTROLS AND FUNCTIONS Front panel BOPTIMIZER MIC jack CPHONES (SILENT CINEMA) jack DSPEAKERS A/B ESTRAIGHT (EFFECT) FPROGRAM Remote control Using the remote control ■Handling the remote control Front panel display Page Rear panel SPEAKER SETUP Speaker placement Surround speakers (SR and SL) Surround back speakers (SBR and SBL) Subwoofer Speaker connections ■Connecting to PRESENCE speaker terminals ■Banana plug connections Page ■FRONT terminals ■CENTER terminals ■SURROUND terminals ■SURROUND BACK terminals ■PRESENCE terminals CONNECTIONS ■Cable indications ■Analog jacks ■Digital jacks ■Video jacks Connecting video components ■Connections for DVD playback ■Connecting to the MULTI CH INPUT jacks ■Connections for other video components ■ VIDEO AUX jacks (on the front panel) Connecting audio components ■Connections for audio components ■Connecting to an external amplifier Connecting the FM and AM antennas ■Connecting the AM loop antenna ■Connecting the AC power cord ■AC OUTLET(S) (SWITCHED).....2 outlets ■Memory back-up Speaker impedance setting Turning on the power AUTO SETUP Introduction Optimizer microphone setup Starting the setup ■If an error screen appears ■If a warning screen appears ■Troubleshooting for auto setup procedure Warnings after auto setup Warning message PLAYBACK Basic operations ■To mute the sound ■To listen with headphones (“SILENT CINEMA”) ■To adjust the tone ■Selecting MULTI CH INPUT ■Front panel operation ■Remote control operation ■Enjoying multi-channelsoftware ■Enjoying 2-channelsoftware in surround ■Listening to high fidelity stereo sound (PURE DIRECT) ■Night listening modes ■Downmixing to 2 channels ■Listening to unprocessed input signals ■Virtual CINEMA DSP Selecting input modes ■Displaying information about the input source 3Press u / d to display the following information about the input signal FM/AM TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting FM stations ■Manually presetting stations Automatic preset tuning options: Selecting preset stations Exchanging preset stations Page XM SATELLITE RADIO TUNING What is XM Satellite Radio XM Satellite Radio connections ■Connecting the XM Connect and Play digital antenna accessory XM Satellite Radio functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations ■Selecting the XM Satellite Radio mode ■Switching XM information in the front panel display ■Displaying XM information in the on XM Satellite Radio search modes ■All Channel Search mode ■Category Search mode ■Preset Search mode ■Direct Number Access mode Setting XM Satellite Radio preset channels While the MEMORY indicator is flashing, press PRESET/TUNING/CH ■Status and error messages RECORDING ■Special considerations when recording DTS software SOUND FIELD PROGRAM DESCRIPTIONS For movie/video sources Page For music sources ADVANCED OPERATIONS Selecting the OSD mode Using the sleep timer ■Setting the sleep timer ■Canceling the sleep timer SET MENU ■AUTO SETUP ■MANUAL SETUP ■SIGNAL INFO Using SET MENU 1 SOUND MENU ■Speaker settings A)SPEAKER SET Surround back speakers SUR. B L/R SP SMLx2 Presence speakers PRESENCE SP NONE Bass out Speaker level ■Speaker distance C)SP DISTANCE ■Center graphic equalizer D)EQUALIZER ■Low-frequencyeffect level E)LFE LEVEL ■Audio settings G)AUDIO SET Dynamic range 2 INPUT MENU ■Input/output assignment ) and B ) and and Input mode Volume Trim Input rename 3 OPTION MENU ■Display settings A)DISPLAY SET Memory guard ■Parameter initialization C)PARAM. INI Zone set Speaker B setting SP B ■XM Radio setting E)XM RADIO SET ADVANCED SETUP MENU ■ADVANCED SETUP menu items REMOTE CONTROL FEATURES Control area ■Controlling this unit ■Controlling other components Setting remote control codes Controlling other components Switching library codes Clearing set up remote control codes EDITING SOUND FIELD PARAMETERS What is a sound field Changing parameter settings ■Elements of a sound field ■Resetting parameters to the factory presets SOUND FIELD PARAMETER DESCRIPTIONS ■DSP LEVEL (DSP level) ■INIT. DLY/P. INIT. DLY (Initial delay) ■ROOM SIZE/P. ROOM SIZE (Room size) ■LIVENESS (Liveness) ■S. INIT. DLY (Surround initial delay) ■S. ROOM SIZE (Surround room size) ■S. LIVENESS (Surround liveness) ■SB INI. DLY (Surround back initial delay) ■REV.TIME (Reverberation time) ■REV.DELAY (Reverberation delay) ■REV. LEVEL (Reverberation level) ■DIALG.LIFT (Dialog lift) For 2ch Stereo: ■DIRECT (Direct) For 7ch Stereo: ■CT LEVEL (Center level) For DTS Neo:6 Music: ■C. IMAGE (Center image) TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control RESETTING THE FACTORY PRESETS GLOSSARY Audio formats ■Dolby Digital ■Dolby Digital EX ■Dolby Pro Logic Sound field programs ■CINEMA DSP ■SILENT CINEMA Audio information ■ITU-R Video signal information ■Component video signal ■Composite video signal ■S-videosignal SPECIFICATIONS LIST OF REMOTE CONTROL CODES APPENDIX-i SATELLITE TUNER (DBS) VCR APPENDIX-ii CD PLAYER DVD PLAYER DVD RECORDER CD RECORDER APPENDIX-iii TAPE DECK APPENDIX-iv