66
Reference
Function List
68
UnitMltPly
Arpeggio Unit Multiply Determines the Arpeggio playback time. For example, if you set a value of
200%, the playback time will be doubled and the tempo halved. If you set a
value of 50%, the playback time will be halved and the tempo doubled.
-
69
VelocityRt
Arpeggio Velocity Rate Determines how much the Velocity of the Arpeggio playback is offset from the
original value. For example, a setting of 100% means the original values are
used.
-*30
*31
70
GateTimeRt
Arpeggio Gate Time Rate Determines how much the Gate Time (length) of the Arpeggio notes is offset
from the original value. A setting of 100% means the original values are used. -*30
71
OutputSw (ArpOutSw)
Arpeggio MIDI Out Switch When set to on, Arpeggio playback and Audition Phrase playback data are
output from the MIDI terminal. 36, 52
*32
72
TransmitCh(ArpTransCh)
Arpeggio MIDI Transmit
Channel
Determines the MIDI transmit channel for Arpeggio playback and Audition
Phrase playback data.
TCh...Arpeggio playback data is transmitted by TransmitCh in the Utility
mode.
-
73
BC/AS1/AS2/FC1/FC2
BC/Assign1/Assign2/FC1/
FC2 Control Number
Sets the control number for the Breath Controller (BC), Assign 1/2 controllers
(AS1/2), and Foot Controllers 1/2 (FC1/2). 40 *32
74
Type
Filter Type Determines the filter type. The parameters differ depending on the selected
type. 27
75
Gain
Filter Gain Determines the Gain (the amount of boost applied to the signal sent to the
Filter). -
76
Cutoff
Filter Cutoff Frequency Determines the cutoff frequency for the Filter, or the central frequency around
which the Filter is applied. 26 *34
77
Resonance (Reso)
Filter Resonance Determines the amount of Resonance (harmonic emphasis) applied to the
signal at the cutoff frequency. 26 *33
78
Reso (Width)
Filter width With the BPFw, this parameter is used to adjust the width of the band of signal
frequencies passed by the filter. -*33
79
Dstnce
Distance Determines the distance between the Cutoff frequencies, for the Dual Filter
types. (The two filters in combination are connected in parallel fashion.) 29
80
HPF Cutoff (HPCtof)
HPF Cutoff Frequency Determines the central frequency for the Key Follow parameter (below) of the
HPF. This parameter is available only when a filter type “LPF12” or “LPF6” is
selected (Normal Voice).
28
81
HP Flw
HPF Cutoff Frequency Key
Follow
Determines the Key Follow setting for the HPF Cutoff frequency (Type=LPF12/
LPF6 only). This parameter varies the center frequency according to the note
number. Positive settings raise the center frequency for higher notes and
lower it for lower notes. Negative settings have the opposite effect.
-
82
TmVel
FEG Time Velocity
Sensitivity
Determines the degree to which velocity affects the pitch change of the Filter
EG. Positive settings cause the pitch change to become faster for a large
Velocity value. Negative values have the opposite effect. This affects only the
specified Segments.
-*21
83
Segmnt
FEG Time Segment -*20
84
LvlVel
FEG Level Velocity
Sensitivity
Determines the sensitivity of the PEG Level (the width of the FEG change) to
velocity. The Curve parameter lets you select from five different preset
velocity curves (graphically indicated in the display), each determining how
velocity affects the Filter EG.
-*21
85
CutofVelSns (CtofVl)
Filter Cutoff Velocity
Sensitivity
Determines the sensitivity of the Cutoff frequency to velocity. -
86
ResoVl
Filter Resonance Velocity
Sensitivity
Determines the sensitivity of the Resonance to velocity. -
87
(FEG) TIME
FEG Time Determines the transition in tone (cutoff frequency) from the moment a Note
On message is received to the point at which the sound stops.
27
88
(FEG) LEVEL
FEG Level 27
89
(FEG) Depth
FEG Depth 27
90
FlwSns
Filter Cutoff Key Follow
Sensitivity
Determines the Filter Key Follow (Filter Scaling) Sensitivity, or how much the
level of the cutoff frequency changes in response to the note number. -
91
CrvVel
FEG Level Velocity Curve Determines the sensitivity of the FEG Level to velocity. This parameter lets
you select from five different preset velocity curves, each determining how
velocity affects the Filter EG.
-*54
92
FlwSns
FEG Time Key Follow
Sensitivity
Determines the sensitivity of the FEG Rate settings (the speed of the FEG
change) to note position. -*22
Ref.
#Display
Parameter Name
Explanation
Related
Page