OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE
RECALL button
VOL
PinP button
RGB 1 RGB 2 | MUTE VOL |
RECALL button
AV1 AV2 AV3 AV4
AUTO PinP SIZE RECALL
If the PinP button on the remote control is pressed MULTI PICTURE will display.
Activating the
Pressing the PinP button once will display 2 pictures.
•This mode can be available from
•The speaker icon can be shifted left and right by pressing the 
and 
SELECT buttons; the audio of the video will be output from
the side on which the speaker icon | RGB2 | |
is located. | ||
AV1 |
•The 
SELECT buttons.
•When the speaker icon appears on
the left of the subscreen, as in the illustration at right, you can use the AV1, AV2, AV3 or AV4 buttons to select the subscreen input mode.
•Pressing the PinP button or the RETURN button will cancel the 2 pictures display.
•"Frequency Mode" in the Setup Menu should be set to Movie when
AV1: Displays the VIDEO input signal of the
MENU
OK
RETURN button
ID | ID SET |
2 Pictures (Split)
Activating the Split mode from the video input screen
Pressing the PinP button one | AV1 | AV2 |
time will display 2 pictures. |
|
|
•The speaker icon can be shifted left and right by pressing the 
and 
SELECT buttons; the audio of the video will be output from the side on which the speaker icon is located.
•The same video input mode cannot
be selected for both screens at the same time.
•Pressing the PinP button again or the RETURN button will cancel the 2 pictures display.
•When the Video input is set to RGB Video, this Split mode is not possible.
•Refer to the table for 2 pictures (Split) mode.
Input terminal |
| AV1~AV4 |
|
| AV1, AV2 |
| RGB1 | RGB2 |
| |
| Sub | PAL | NTSC3.58 | 576i | 480i | 1080i/50 1080i/60 | 720p/60 | STB | Component |
|
| Main | SECAM | NTSC4.43 | 576p | 480p | Sub | ||||
AV1 | PAL, SECAM |
|
|
|
|
|
|
| Main | |
|
|
|
|
|
|
|
|
| ||
~AV4 | NTSC3.58/4.43 |
|
|
|
|
|
|
|
|
|
| 576i, 576p |
|
|
|
|
|
|
|
|
|
AV1 | 480i, 480p |
|
|
|
|
|
|
|
|
|
1080i/50 |
|
|
|
|
|
|
|
|
| |
AV2 |
|
|
|
|
|
|
|
|
| |
1080i/60 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
| 720p/60 |
|
|
|
|
|
|
|
|
|
RGB1 | STB |
|
|
|
|
|
|
|
|
|
RGB2 | Component |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ( | : Available) |
|
NOTE |
|
|
|
|
|
|
|
|
|
|
•Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not change to power save mode.
•Please be careful since image retention will occur if the plasma monitor is left in a MULTI PICTURE display state for a long period of time.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the monitor.
•The display will go out in approximately 6 seconds.
VIDEO
OFF
Input mode
AV1
Composite 
Signal mode
34
