Error indications on the front display
Message | Cause | Remedy | |
Access denied | Access to the PC is denied. | Configure the sharing settings and select the unit as a device to which music contents are shared | |
|
| ||
|
|
| |
| The unit cannot access the USB device. | Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. | |
|
|
| |
| The unit cannot access the iPod. | Turn off the iPod and turn it on again. | |
|
|
| |
Access error | The connected iPod is not supported by the unit. | Use an iPod supported by the unit (p.65). | |
|
|
| |
| There is a problem with the signal path from the network to the unit. | Make sure your router and modem are turned on. | |
|
| ||
| Check the connection between the unit and your router (or hub) (p.37). | ||
|
| ||
|
|
| |
Check SP Wires | The speaker cables short circuit. | Twist the bare wires of the cables firmly and connect to the unit and speakers properly. | |
|
|
| |
Internal Error | An internal error has occurred. | Contact the nearest authorized Yamaha dealer or service center. | |
|
|
| |
MHL Overloaded | An overcurrent is flowing through the | Turn off the unit and check the connection between the unit and mobile device. | |
device. | |||
|
| ||
|
|
| |
No content | There are no playable files in the selected folder. | Select a folder that contains files supported by the unit. | |
|
|
| |
No device | The unit cannot detect the USB device. | Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. | |
|
| ||
The unit cannot detect the iPod. | Turn off the iPod and then turn it on again. | ||
| |||
|
|
| |
Please wait | The unit is preparing for connecting to the network. | Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn | |
it on again. | |||
|
| ||
|
|
| |
RemID Mismatch | The remote control IDs of the unit and the remote control are not | Change the remote control ID of the unit or the remote control (p.120). | |
identical. | |||
|
| ||
|
|
| |
Remote Off | The unit cannot be operated from remote control because the | Use the controls on the front panel. To use the remote control, set “REMOTE SENSOR” in the | |
remote control sensor on the main unit is turned off. | “ADVANCED SETUP” menu to “ON” (p.120). | ||
| |||
|
|
| |
| The unit cannot play back the songs stored on the USB device for | Check the song data. If it cannot be played on another device, the song data may be defective. | |
| some reasons. | ||
|
| ||
|
|
| |
| The unit cannot play back the songs stored on the iPod for some | Check the song data. If it cannot be played on the iPod itself, the song data or storage area may be | |
Unable to play | reason. | defective. | |
|
| ||
| The unit cannot play back the songs stored on the PC for some | Check if the format of files you are trying to play is supported by the unit. For information about the | |
| formats supported by the unit, see “Playing back music stored on media servers (PCs/NAS)” (p.72). If | ||
| reason. | the unit supports the file format, but still cannot play back any files, the network may be overloaded with | |
|
| heavy traffic. | |
|
|
| |
USB Overloaded | An overcurrent is flowing through the USB device. | Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. | |
|
|
| |
Version error | Firmware update is failed. | Update the firmware again. | |
|
|
|
APPENDIX ➤ Error indications on the front display | En 136 |
|
|