Yamaha RX-V3300 ■IMPEDANCE SELECTOR switch

SPEAKER SETUP

■IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the upper or lower position according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode.

IMPEDANCE SELECTOR switch

IMPEDANCE SELECTOR

	SET BEFORE POWER ON			ZONE 2 OUT	: 6ΩMIN./SPEAKER
SELECTEUR D'INPEDANCE				FRONT	: 6ΩMIN./SPEAKER
				REAR	: 4ΩMIN./SPEAKER
				CENTER	: 4ΩMIN./SPEAKER
		ZONE 2 OUT	: 8ΩMIN./SPEAKER	REAR CENTER : 4ΩMIN./SPEAKER
		FRONT	: 8ΩMIN./SPEAKER	MAIN A OR B : 4ΩMIN./SPEAKER
		REAR	: 8ΩMIN./SPEAKER
				A + B : 8ΩMIN./SPEAKER
		CENTER	: 8ΩMIN./SPEAKER
		REAR CENTER : 8ΩMIN./SPEAKER
		MAIN A OR B : 8ΩMIN./SPEAKER

+
L
L	AC IN
FRONT	AC OUTLETS
EFFECT
L
REAR
(SURROUND)

CENTER	IMPEDANCE SELECTOR
	SET BEFORE POWER ON			ZONE 2 OUT	: 6ΩMIN./SPEAKER
	SELECTEUR D'INPEDANCE			FRONT	: 6ΩMIN./SPEAKER
				REAR	: 4ΩMIN./SPEAKER
		ZONE 2 OUT	: 8ΩMIN./SPEAKER	CENTER : 4ΩMIN./SPEAKER
				REAR CENTER : 4ΩMIN./SPEAKER
L		FRONT	: 8ΩMIN./SPEAKER	MAIN A OR B : 4ΩMIN./SPEAKER
		REAR	: 8ΩMIN./SPEAKER	A + B : 8ΩMIN./SPEAKER
		CENTER : 8ΩMIN./SPEAKER
B		REAR CENTER : 8ΩMIN./SPEAKER
		MAIN A OR B : 8ΩMIN./SPEAKER
MAIN
L
A

(U.S.A. model)

Switch	Speaker	Impedance level
position
	Zone 2	The impedance of each speaker must be 6 Ω or higher.
	Front	The impedance of each speaker must be 6 Ω or higher.
	Effect
		The impedance of each speaker must be 4 Ω or higher.
	Rear	[Australia model]
		The impedance of each speaker must be 6 Ω or higher.
Upper	Center	The impedance must be 4 Ω or higher.
	Rear	The impedance must be 4 Ω or higher.
		[Australia model]
	Center
		The impedance must be 6 Ω or higher.
		If you use one set of main speakers, the impedance of
	Main	each speaker must be 4 Ω or higher.
		If you use two sets of main speakers, the impedance of
		each speaker must be 8 Ω or higher.
	Zone 2	The impedance of each speaker must be 8 Ω or higher.
	Front	The impedance of each speaker must be 8 Ω or higher.
	Effect
	Rear	The impedance of each speaker must be 8 Ω or higher.
	Center	The impedance must be 8 Ω or higher.
Lower
	Rear	The impedance must be 8 Ω or higher.
	Center
		If you use one set of main speakers, the impedance of
		each speaker must be 8 Ω or higher.
	Main	If you use two sets of main speakers, the impedance of
		each speaker must be 16 Ω or higher.
		[U.S.A. model]
		The impedance of each speaker must be 8 Ω or higher.

14