BASIC RECORDING

REC OUT/ZONE 2 allows you to record one source while watching and/or listening to another source.

Recording adjustments and other operations are performed from the recording components. Refer to the operation instructions for these components.

12

VOLUME

NATURAL SOUND AV RECEIVER RX-V3300

STANDBY /ON

INPUTMODE

SPEAKERS

 

PRESET/

PRESET

TUNING

A

B

A/B/C/D/E

TUNING

/TUNING FM/AM MEMORY

MODE

SILENT

MAN'L/AUTO FM AUTO/MAN'L MONO

BASS PROCESSOR

 

 

 

6CH

EXTENSION DIRECT

 

 

STEREO PROGRAM

INPUT

+

+

 

 

BASS

TREBLE

REC OUT /ZONE 2

 

VIDEO AUX

1 Turn on the power to this unit and all connected components.

2 Select the source component you want to record from by using REC OUT/ZONE 2.

To record the current input source that you are watching or listening to, set REC OUT/ZONE 2

to SOURCE/REMOTE.

SOURCE /REMOTE

DVD MD/TAPE

D-TV/LDCD-R

CBL/SAT TUNER

VCR 1

CD

VCR2

/DVRPHONO V-AUX

REC OUT/ZONE 2

To record a source other than the one that you are watching or listening to, set REC OUT/ZONE 2 to the source you want to record.

SOURCE /REMOTE

DVD MD/TAPE

D-TV/LDCD-R

CBL/SAT TUNER

VCR 1

CD

VCR2

/DVRPHONO V-AUX

REC OUT/ZONE 2

Note

At this setting, you can change the source to listen to or watch during recording by rotating INPUT (one of the input selector buttons on the remote control).

3 Start playback (or select a broadcast station) on the source component.

4 Start recording on the recording component.

y

Setting REC OUT/ZONE 2 to SOURCE/REMOTE and using the BGV function (see page 30) allows the recording of audio and video from a different source.

Notes

Do a test recording before you start an actual recording.

When this unit is set in the standby mode, you cannot record between other components connected to this unit.

The setting of BASS, TREBLE, BASS EXTENSION, VOLUME, “3 L/R BALANCE” on the SET MENU and DSP programs does not affect the recorded material.

A source connected to the 6CH INPUT jacks of this unit cannot be recorded.

S-video and composite video signals pass independently through this unit’s video circuits. Therefore, when recording or dubbing video signals, if your video source component is connected to provide only an S-video (or only a composite video) signal, you can record only an S-video (or only a composite video) signal by your VCR.

A given input source is not output on the same REC OUT channel. (For example, the signal input from VCR 1 IN is not output on VCR 1 OUT.)

Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws.

If you playback a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals.

Special considerations when recording DTS software

The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources that have DTS signals recorded on them, the following considerations and adjustments need to be made.

For LDs, DVDs and CDs encoded with DTS, when your player is compatible with the DTS format, follow its operation instruction to make a setting so that the analog signal will be output from the player.

Timer playback/recording

This unit can perform playback or recording with an external timer (not supplied). Refer to the operation instruction for the component and the timer to be used.

Notes

The stored data such as input source will be reflected in the playback or recording with the timer.

If you do not want any sound output during the recording with a timer, turn the volume down.

Memory back-up

The memory back-up circuit prevents the stored data (input source, volume level, set menu settings and so on) from being lost even if this unit is in the standby mode (disconnected from the AC outlet). However if the timer is turned off for more than one week, the stored data will be lost.

OPERATION

BASIC

 

 

English

45