Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V659 Connecting the FM and AM antennas, ■Connecting the AM loop antenna, into place, 1Set up the AM loop antenna, 4 Release the tab of the AM ANT terminal back

1 132

Download 132 pages, 2.35 Mb

CONNECTIONS

Connecting the FM and AM antennas

Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

Notes

•Be sure to set the tuner frequency step (Asia and General models only) according to the frequency spacing in your area (see page 98).

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

Indoor FM antenna

(supplied except for U.K. model)

AM loop antenna

(supplied except for U.K. model)

2Press and hold the tab of the AM ANT terminal.

3Insert one of the AM loop antenna lead wires into the AM ANT terminal.

	(U.S.A. model)	4 Release the tab of the AM ANT terminal back
75Ω UNBAL.	TUNER	into place.
75Ω UNBAL.	AM
ANT	GND ANT
FM	GND ANT
	Outdoor AM antenna
	Use a 5 to 10 m (16.4 to 32.8 ft)
	of vinyl-covered wire extended
	outdoors from a window.

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

■Connecting the AM loop antenna

1Set up the AM loop antenna.

5Repeat steps 2 through 4 to connect the other lead wire to the GND terminal.

y

Once you have properly connected the AM loop antenna to this unit, orient the AM loop antenna for the best reception when you tune into AM stations (see page 52).

28

Contents

Page IMPORTANT SAFETY INSTRUCTIONS •Explanation of Graphical Symbols 4Follow Instructions – All operating and use instructions should be followed overturn a)When the power-supplycord or plug is damaged FCC INFORMATION (for US customers) 1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT NOTE: CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Supplied accessories Installing batteries in the remote control CONTROLS AND FUNCTIONS Front panel C D EF G H 8MEMORY (MAN’L/AUTO FM) 9TUNING MODE (AUTO/MAN’L) 0ZONE 2 ON/OFF Turns on Zone 2 or sets it to the standby mode (see page 106) AZONE CONTROL Remote control ■Controlling this unit 8Cursor buttons u / d / j / i, ENTER 9RETURN Returns to the previous menu level when adjusting the “SET MENU” parameters 0TRANSMIT indicator Flashes while the remote control is sending infrared signals ■Controlling the TUNER functions ■Using the remote control Front panel display FSTANDARD indicator GSP A B indicators Light up according to the set of front speakers selected HHeadphones indicator Lights up when headphones are connected (see page 40) Rear panel ■VOLTAGE SELECTOR (Asia and General models only) CONNECTIONS Placing speakers Connecting speakers FRONT terminals CENTER terminals SURROUND terminals SURROUND BACK terminals PRESENCE/ZONE2 terminals ■Connecting the speaker cable ■Connecting to the PRESENCE/ZONE2 speaker terminals ■Connecting the banana plug (except U.K., Europe and Asia models) Information on jacks and cable plugs ■Audio jacks ■Video jacks Audio and video signal flow ■Audio signal flow for AUDIO OUT (REC) COAXIAL OPTICAL AUDIO Connecting a TV Connecting a DVD player, a DVD recorder, a VCR or an STB ■Connecting a DVD player ■Connecting a DVD recorder ■Connecting a VCR ■Connecting an STB Connecting a CD player, an MD player, a tape deck or a turntable Connecting a YAMAHA iPod universal dock Connecting an external amplifier Connecting a multi-formatplayer or an external decoder Connecting a game console, a video camera or a portable audio player Connecting the FM and AM antennas ■Connecting the AM loop antenna Connecting the power cable ■AC OUTLET(S) (SWITCHED) Setting the speaker impedance Turning on and off the power ■Turning on this unit ■Turning off this unit AUTO SETUP Connecting the optimizer microphone Using AUTO SETUP AUTO •Select “AUTO” to automatically run the entire “AUTO SETUP” procedure 5Press d to select “START” and then press ENTER to start the setup procedure The display changes as follows RESULT:SIZE 8Press ENTER to return to the top “RESULT:EXIT” display RESULT:EXIT Make sure the pointer is pointing at “SET” and “CANCEL” and then press Choices: SET, CANCEL SET ■If an error screen appears ■If a warning screen appears PLAYBACK •Select “TREBLE” to adjust the high-frequencyresponse •Select “BASS” to adjust the low-frequencyresponse •Speaker and headphone adjustments are stored independently When “TONE BYPASS” is set to “AUTO” If you increase or decrease the USING AUDIO FEATURES Using SILENT CINEMA Selecting the night listening mode Muting the audio output Selecting the input mode Using the sleep timer Adjusting the speaker level Selecting the Compressed Music Enhancer mode Selecting the MULTI CH INPUT component Enjoying multi-channelsources in 2-channelstereo Enjoying unprocessed input sources USING VIDEO FEATURES Displaying the input source information Selecting the OSD mode Playing video sources in the background ENJOYING SURROUND SOUND Enjoying multi-channelsources in surround Enjoying 2-channelsources in surround Using Virtual CINEMA DSP RECORDING FM/AM TUNING Automatic tuning Manual tuning Automatic preset tuning ■Automatic preset tuning options Manual preset tuning Selecting preset stations Exchanging preset stations 3Select preset station “A5” using A/B/C/D/E and PRESET/TUNING/CH l / h 4Press EDIT again XM® SATELLITE RADIO TUNING ■Information from XM Satellite Radio Inc XM Satellite Radio controls and functions ■Front panel functions ■Remote control functions Activating XM Satellite Radio Basic XM Satellite Radio operations Selecting the XM Satellite Radio search mode ■All Channel Search mode ■ Category Search mode ■Preset Search mode ■Direct Number Access mode Setting the XM Satellite Radio preset channels Displaying the XM Satellite Radio information ■Displaying the XM Satellite Radio information in the front panel display ■Displaying the XM Satellite Radio information in the OSD SOUND FIELD PROGRAMS ■Elements of a sound field Selecting sound field programs ■Front panel operations ■Remote control operations Sound field program descriptions ■For movie/video sources ■For music sources Changing sound field parameter settings ■Sound field parameter descriptions Page Page AUTO “TREBLE” are set to 0 dB (see page 39) channels and output from the front left and right speakers subwoofer in the following cases: – “LFE/BASS OUT” is set to “BOTH” (see page 88) OFF DIMENSION Control range: –3(towards the rear) to +3 (towards the front) Initial setting: STD (standard) CENTER WIDTH Sound field program speaker layouts Page Page Page SET MENU ■Auto setup AUTO SETUP ■Manual setup MANUAL SETUP ■Signal information SIGNAL INFO Using SET MENU 1 SOUND MENU ■Speaker settings A)SPEAKER SET Center speaker CENTER SP Surround back speakers SUR. B L/R SP Choices: NONE, SML, LRG SML Choices: NONE, SMLx1, SMLx2, LRGx1, LRGx2 Bass out BOTH Subwoofer phase SUBWOOFER PHASE NORMAL Crossover CROSS OVER Speaker level ■Speaker distance C)SP DISTANCE ■Center graphic equalizer D)EQUALIZER ■Low-frequencyeffect level E)LFE LEVEL ■Audio settings G)AUDIO SET Dynamic range 2 INPUT MENU ■Input/output assignment Input mode Input rename Volume Trim 3 OPTION MENU 3OPTIONMENU 1/2 ■Display settings A)DISPLAY SET Memory guard ■Parameter initialization C)PARAM. INI Zone set ■XM Radio setting E)XM RADIO SET (U.S.A. model only) ADVANCED SETUP ■Speaker impedance SP IMP ■Factory presets PRESET ■Remote control AMP ID REMOTE AMP ■Remote control TUNER ID REMOTE TUN ■Remote control XM ID REMOTE XM REMOTE CONTROL FEATURES Controlling this unit, a TV, or other components ■Controlling a TV ■Controlling other components Remote Control Code Default Settings Input Library Default DVD Setting library codes ■Setting remote control AMP ID library codes ■Setting remote control TUNER ID library ■Setting remote control XM ID library Resetting all remote control codes USING MULTI-ZONECONFIGURATION Connecting Zone ■Using the external amplifier ■Using the internal amplifier of this unit Controlling Zone ■Controlling Zone 2 with the front panel ■Setting the remote control to the Zone mode ■Controlling Zone 2 with the remote control USING iPod® Controlling iPod ■Controlling iPod without using the OSD ■Controlling iPod using the OSD RESETTING THE SYSTEM TROUBLESHOOTING ■General Page Page ■Tuner ■XM Satellite Radio (U.S.A. model only) ■Remote control ■iPod ■AUTO SETUP After AUTO SETUP Warning message GLOSSARY Audio information ■Dolby Digital ■Dolby Digital EX ■Dolby Pro Logic Video information ■Component video signal ■Composite video signal ■S-videosignal Sound field program information ■CINEMA DSP ■SILENT CINEMA ■Virtual CINEMA DSP SPECIFICATIONS LIST OF REMOTE CONTROL CODES CABLE TV RECEIVER CABLE/PVR DBS/PVR SATELLITE RECEIVER APPENDIX-ii VCR PVR APPENDIX-iii LD PLAYER DVD PLAYER DVD RECORDER APPENDIX-iv TAPE DECK CD PLAYER TUNER CD RECORDER APPENDIX-v OTHER AUDIO APPENDIX-vi