Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V800 Connecting to an External, Amplifier, Connecting an External Decoder, 1MAIN jacks, 3CENTER jack, 2SUBWOOFER jack, 4REAR (SURROUND) jacks

1 82

Download 82 pages, 3.04 Mb

CONNECTIONS

Connecting to an External

Amplifier

If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the OUTPUT jacks as follows.

Note

•When RCA pin plugs are connected to the OUTPUT jacks for output to an external amplifier, it is not necessary to use the

corresponding SPEAKERS terminals.

OUTPUT

MAIN

1 R L

2

SUB

WOOFER

CENTER

3

4

R REAR (SURROUND) L

1MAIN jacksMain channel line output jacks.

Note

•The signals output through these jacks are affected by the BASS, TREBLE and BASS EXTENSION settings.

2SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (low- frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack.

Notes

•Adjust the volume level of the subwoofer with the control on the subwoofer. The subwoofer volume cannot be adjusted from this unit.

•Depending on the settings of “1 SPEAKER SET”, “10A LFE LEVEL” and “11 DTS LFE LEVEL” on the SET MENU, some signals may not be output from the SUBWOOFER jack.

3CENTER jackCenter channel line output jack.4REAR (SURROUND) jacksRear channel line output jacks.

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left and right MAIN, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels.

Notes

•When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs.

•When you select 6CH INPUT as the input source, changing items 1A to 1E on the SET MENU is not affected.

18

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Checking the Package Contents Installing Batteries in the Remote Control CONTROLS AND FUNCTIONS Front Panel qEFFECT wA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control Description of the Numeric Buttons Using the Remote Control Front Panel Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Page Connecting Video Components Page Connecting the Speakers Page Connecting to an External Amplifier Connecting an External Decoder IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ON-SCREENDISPLAY (OSD) OSD Modes P01 CONCERT HALL Selecting the OSD Mode SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E ADJUSTING THE SPEAKER OUTPUT LEVELS Before You Begin Using the Test Tone (TEST DOLBY SUR.) TEST DOLBY SUR 4 Press LEVEL repeatedly to select the speaker to be adjusted While adjusting, the test tone is heard from the selected speaker 6 When the adjustment is complete, press TEST BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4 Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5 Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■When you have finished using this unit Input Modes and Indications ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program Normal Stereo Reproduction TUNING Connecting the Antennas Automatic (or Manual) Tuning Presetting Stations Tuning in to a Preset Station Exchanging Preset Stations BASIC RECORDING SET MENU Adjusting the Items on the SET MENU SET MENU 1/4 1SPEAKER SET (speaker mode settings) 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 LOW FRQ TEST 4HP TONE CTRL (headphone tone control) 5CENTER GEQ (center graphic equalizer) 6 INPUT RENAME 7 I/O ASSIGNMENT 8INPUT MODE (initial input mode) 10DOLBY D. SET (Dolby Digital set) 11 DTS LFE LEVEL 12 6.1/ES AUTO 13 SP DELAY TIME 14DISPLAY SET 15 MEMORY GUARD ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER Setting the Sleep Timer Canceling the Sleep Timer REMOTE CONTROL FEATURES Selector Dial Commonly Used Buttons in Any Position of the Selector Dial Controlling the Components Connected to This Unit Button Names and Functions in Each Position ■DVD/LD position ■DVD MENU position •DVD MENU operations cannot be performed for some DVD players ■VCR position ■CBL/SAT position ■TV position Setting the Manufacturer Code Programming a New Remote Control Function (Learn Feature) Returning to the Factory Setting ZONE Zone 2 Connections SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Adventure ES *2 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds These programs express an immense sound field and a large surround effect. They also give depth to the sound from the main speakers to recreate the realistic sound of a Dolby Stereo theater SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field Sound Field Program Parameters Changing Parameter Settings P04 ROCK CONCERT Resetting a Parameter to the Factory-setValue Digital Sound Field Parameter Descriptions ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RS.DELAY (right surround delay) TROUBLESHOOTING Page Page ■Tuner ■Remote control SPECIFICATIONS TV CABLE TV SATELLITE TUNER (DSS) VCR DVD PLAYER LD PLAYER CD PLAYER CD RECORDER MD RECORDER TAPE DECK () Page Quick Reference Card AMP/TUN DSP/TUN TAPE/MD (CD-R) DVD/LD DVD MENU VCR CBL/SAT