Yamaha RX-V800 ■Tuner

TROUBLESHOOTING

■Tuner

	Problem	Cause	Remedy	Refer to
	Problem	Cause	Remedy	page
				page

	FM stereo	The characteristics of FM stereo broadcasts	Check the antenna connections.	30, 31
	reception is noisy.	may cause this problem when the	Try using a high-quality directional FM
		transmitter is too far away or the antenna	antenna.
		input is poor.	Use the manual tuning method.

	There is distortion,	There is multipath interference.	Adjust the antenna position to eliminate	30
	and clear reception		multipath interference.
	cannot be obtained
FM	even with a good
FM	FM antenna.

	The desired station	The station is too weak.	Use the manual tuning method.	30, 31
	cannot be tuned in		Use a high-quality directional FM antenna.
	with the automatic
	tuning method.

	Previously preset	The unit has been disconnected for a long	Re-store the stations.	32
	stations can no	period.
	longer be tuned in.

	The desired station	The signal is weak or the antenna	Tighten the AM loop antenna connections and	30, 31
	cannot be tuned in	connections are loose.	orient it for best reception.
	with the automatic		Use the manual tuning method.
	tuning method.

	There are	Noises result from lightning, fluorescent	Use an outdoor antenna and a ground wire.	30
AM	continuous	lamps, motors, thermostats and other	This will help somewhat, but it is difficult to
AM	crackling and	electrical equipment.	eliminate all noise.
	hissing noises.

	There are buzzing	A TV set is being used nearby.	Move this unit away from the TV.	—
	and whining noises
	(especially in the
	evening).

APPENDIX

English

69

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Checking the Package Contents Installing Batteries in the Remote Control CONTROLS AND FUNCTIONS Front Panel qEFFECT wA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control Description of the Numeric Buttons Using the Remote Control Front Panel Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Page Connecting Video Components Page Connecting the Speakers Page Connecting to an External Amplifier Connecting an External Decoder IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ON-SCREENDISPLAY (OSD) OSD Modes P01 CONCERT HALL Selecting the OSD Mode SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E ADJUSTING THE SPEAKER OUTPUT LEVELS Before You Begin Using the Test Tone (TEST DOLBY SUR.) TEST DOLBY SUR 4 Press LEVEL repeatedly to select the speaker to be adjusted While adjusting, the test tone is heard from the selected speaker 6 When the adjustment is complete, press TEST BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4 Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5 Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■When you have finished using this unit Input Modes and Indications ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program Normal Stereo Reproduction TUNING Connecting the Antennas Automatic (or Manual) Tuning Presetting Stations Tuning in to a Preset Station Exchanging Preset Stations BASIC RECORDING SET MENU Adjusting the Items on the SET MENU SET MENU 1/4 1SPEAKER SET (speaker mode settings) 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 LOW FRQ TEST 4HP TONE CTRL (headphone tone control) 5CENTER GEQ (center graphic equalizer) 6 INPUT RENAME 7 I/O ASSIGNMENT 8INPUT MODE (initial input mode) 10DOLBY D. SET (Dolby Digital set) 11 DTS LFE LEVEL 12 6.1/ES AUTO 13 SP DELAY TIME 14DISPLAY SET 15 MEMORY GUARD ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER Setting the Sleep Timer Canceling the Sleep Timer REMOTE CONTROL FEATURES Selector Dial Commonly Used Buttons in Any Position of the Selector Dial Controlling the Components Connected to This Unit Button Names and Functions in Each Position ■DVD/LD position ■DVD MENU position •DVD MENU operations cannot be performed for some DVD players ■VCR position ■CBL/SAT position ■TV position Setting the Manufacturer Code Programming a New Remote Control Function (Learn Feature) Returning to the Factory Setting ZONE Zone 2 Connections SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Adventure ES *2 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds These programs express an immense sound field and a large surround effect. They also give depth to the sound from the main speakers to recreate the realistic sound of a Dolby Stereo theater SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field Sound Field Program Parameters Changing Parameter Settings P04 ROCK CONCERT Resetting a Parameter to the Factory-setValue Digital Sound Field Parameter Descriptions ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RS.DELAY (right surround delay) TROUBLESHOOTING Page Page ■Tuner ■Remote control SPECIFICATIONS TV CABLE TV SATELLITE TUNER (DSS) VCR DVD PLAYER LD PLAYER CD PLAYER CD RECORDER MD RECORDER TAPE DECK () Page Quick Reference Card AMP/TUN DSP/TUN TAPE/MD (CD-R) DVD/LD DVD MENU VCR CBL/SAT