Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V800 TUNING, Connecting the Antennas, ■Connecting the AM loop antenna 2, ■Connecting the indoor FM antenna, 100 kHz/10 kHz, Other area: 50 kHz/9 kHz

1 82

Download 82 pages, 3.04 Mb

TUNING

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength.

Connect each antenna correctly to the designated terminals.

FREQUENCY STEP switch (China and general models only)

■Connecting the AM loop antenna 2 1

100 kHz/10 kHz

50 kHz/ 9 kHz

FM AM

FREQUENCY

STEP

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (locating at the rear) according to the frequency spacing in your area.

North, Central and South America:100 kHz/10 kHz

Other area: 50 kHz/9 kHz

Before setting this switch, disconnect the AC power plug of this unit from the AC outlet.

	4	3
	4	5
		5

Antenna stand

1 Press and hold the tab to unlock the terminal hole.

AM loop antenna			Indoor FM
(included)			Indoor FM
(U.S.A. model)			antenna
(U.S.A. model)			(included)
DIGITAL OUTPUT	TUNER
MD/	TUNER
TAPE
	AM
CD-R	ANT
OPTICAL	GND
CD
CD-R	75 UNBAL.
	FM
	ANT
DVD
	GND
D-TV
/LD
OPTICAL
COAXIAL
CD
CBL
/SAT
	IN
	OUT	Ground (GND terminal)
DIGITAL INPUT	REMOTE CONTROL	For maximum safety and minimum
		interference, connect the antenna GND
		terminal to a good earth ground. A
		good earth ground is a metal stake
		driven into moist earth.

2 Insert the AM loop antenna lead wires into the AM ANT and GND terminals.3 Release the tab to lock the lead wires.Lightly pull the lead wires to confirm a good connection.4 Attach the loop antenna to the antenna stand.5 Orient the AM loop antenna so that the best reception is obtained.

y

•The AM loop antenna can be removed from the stand and attached to a wall, etc.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

■Connecting the indoor FM antennaConnect the included indoor FM antenna to the 75Ω UNBAL. FM ANT terminal.

Note

•Do not connect an outdoor FM antenna and the indoor FM antenna at the same time.

30

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Checking the Package Contents Installing Batteries in the Remote Control CONTROLS AND FUNCTIONS Front Panel qEFFECT wA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control Description of the Numeric Buttons Using the Remote Control Front Panel Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Page Connecting Video Components Page Connecting the Speakers Page Connecting to an External Amplifier Connecting an External Decoder IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ON-SCREENDISPLAY (OSD) OSD Modes P01 CONCERT HALL Selecting the OSD Mode SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E ADJUSTING THE SPEAKER OUTPUT LEVELS Before You Begin Using the Test Tone (TEST DOLBY SUR.) TEST DOLBY SUR 4 Press LEVEL repeatedly to select the speaker to be adjusted While adjusting, the test tone is heard from the selected speaker 6 When the adjustment is complete, press TEST BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4 Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5 Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■When you have finished using this unit Input Modes and Indications ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program Normal Stereo Reproduction TUNING Connecting the Antennas Automatic (or Manual) Tuning Presetting Stations Tuning in to a Preset Station Exchanging Preset Stations BASIC RECORDING SET MENU Adjusting the Items on the SET MENU SET MENU 1/4 1SPEAKER SET (speaker mode settings) 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 LOW FRQ TEST 4HP TONE CTRL (headphone tone control) 5CENTER GEQ (center graphic equalizer) 6 INPUT RENAME 7 I/O ASSIGNMENT 8INPUT MODE (initial input mode) 10DOLBY D. SET (Dolby Digital set) 11 DTS LFE LEVEL 12 6.1/ES AUTO 13 SP DELAY TIME 14DISPLAY SET 15 MEMORY GUARD ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER Setting the Sleep Timer Canceling the Sleep Timer REMOTE CONTROL FEATURES Selector Dial Commonly Used Buttons in Any Position of the Selector Dial Controlling the Components Connected to This Unit Button Names and Functions in Each Position ■DVD/LD position ■DVD MENU position •DVD MENU operations cannot be performed for some DVD players ■VCR position ■CBL/SAT position ■TV position Setting the Manufacturer Code Programming a New Remote Control Function (Learn Feature) Returning to the Factory Setting ZONE Zone 2 Connections SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Adventure ES *2 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds These programs express an immense sound field and a large surround effect. They also give depth to the sound from the main speakers to recreate the realistic sound of a Dolby Stereo theater SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field Sound Field Program Parameters Changing Parameter Settings P04 ROCK CONCERT Resetting a Parameter to the Factory-setValue Digital Sound Field Parameter Descriptions ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RS.DELAY (right surround delay) TROUBLESHOOTING Page Page ■Tuner ■Remote control SPECIFICATIONS TV CABLE TV SATELLITE TUNER (DSS) VCR DVD PLAYER LD PLAYER CD PLAYER CD RECORDER MD RECORDER TAPE DECK () Page Quick Reference Card AMP/TUN DSP/TUN TAPE/MD (CD-R) DVD/LD DVD MENU VCR CBL/SAT