Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V800 ADJUSTING THE SPEAKER OUTPUT LEVELS, Before You Begin, SUR.), Using the Test Tone (TEST DOLBY, the video monitor, 1 Press STANDBY/ON to

1 82

Download 82 pages, 3.04 Mb

ADJUSTING THE SPEAKER OUTPUT LEVELS

This section explains how to adjust the speaker output levels by using the test tone generator. When this adjustment is made, the output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decoder.

Note

•Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone.

Before You Begin

1

INPUT

VOLUME

6CH INPUT

INPUT MODE

STANDBY

/ON

PRESET/

PRESET

TUNING

A/B/C/D/E

TUNING

/TUNING FM/AM MEMORY

MODE

BASS

TREBLE

SPEAKERS

BASS

PROCESSOR

TUNER

EDIT

MAN'L/AUTO FM AUTO/MAN'L MONO

A

B

EXTENSION

DIRECT

PHONES

S VIDEO

VIDEO

L AUDIO R OPTICAL

EFFECT

PROGRAM

ON

OFF

DSP

SILENT

–

+

–

+

VIDEO AUX

2	3		3
1 Press STANDBY/ON to
turn on the power. Turn on			/ON
			STANDBY
the video monitor.
2 Press SPEAKERS A or B		A	B
		SPEAKERS

to select the main speakers to be used.If you are using two sets of the main speakers, press both A and B.

3 Set BASS and TREBLE on the front panel to the center position and set BASS EXTENSION to OFF.

BASS TREBLE

BASS PROCESSOR

EXTENSION DIRECT

Using the Test Tone (TEST DOLBY

SUR.)

Use the test tone to balance the output levels of the 5 speakers required for a surround sound system. The adjustment of each speaker output level should be made at your listening position with the remote control. After completing the adjustments, use VOLUME +/– at your listening position to check if the adjustments are satisfactory.

2,6 1

5 4

3

1 Set the selector dial to theAMP/TUN (or DSP/TUN) position.2 Press TEST to output the test tone.3 Adjust the volume so you can hear the test tone.

The test tone is heard from the left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker in order. The tone is produced for 2.5 seconds each time.

LEFT RIGHT

(TEST LEFT) (TEST RIGHT)

– + – +

OFF

CENTER

(TEST CENTER)

Set to OFF.

LEFT SURROUND	RIGHT SURROUND
(TEST L SUR.)	(TEST R SUR.)

22

Contents

Page SAFETY INSTRUCTIONS I CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT III CAUTION CONTENTS FEATURES GETTING STARTED Checking the Package Contents Installing Batteries in the Remote Control CONTROLS AND FUNCTIONS Front Panel qEFFECT wA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control Description of the Numeric Buttons Using the Remote Control Front Panel Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Page Connecting Video Components Page Connecting the Speakers Page Connecting to an External Amplifier Connecting an External Decoder IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ON-SCREENDISPLAY (OSD) OSD Modes P01 CONCERT HALL Selecting the OSD Mode SPEAKER MODE SETTINGS Summary of SPEAKER SET Items 1A through 1E ADJUSTING THE SPEAKER OUTPUT LEVELS Before You Begin Using the Test Tone (TEST DOLBY SUR.) TEST DOLBY SUR 4 Press LEVEL repeatedly to select the speaker to be adjusted While adjusting, the test tone is heard from the selected speaker 6 When the adjustment is complete, press TEST BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4 Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5 Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■When you have finished using this unit Input Modes and Indications ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program Normal Stereo Reproduction TUNING Connecting the Antennas Automatic (or Manual) Tuning Presetting Stations Tuning in to a Preset Station Exchanging Preset Stations BASIC RECORDING SET MENU Adjusting the Items on the SET MENU SET MENU 1/4 1SPEAKER SET (speaker mode settings) 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D LFE/BASS OUT 1E MAIN LEVEL 2 LOW FRQ TEST 4HP TONE CTRL (headphone tone control) 5CENTER GEQ (center graphic equalizer) 6 INPUT RENAME 7 I/O ASSIGNMENT 8INPUT MODE (initial input mode) 10DOLBY D. SET (Dolby Digital set) 11 DTS LFE LEVEL 12 6.1/ES AUTO 13 SP DELAY TIME 14DISPLAY SET 15 MEMORY GUARD ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER Setting the Sleep Timer Canceling the Sleep Timer REMOTE CONTROL FEATURES Selector Dial Commonly Used Buttons in Any Position of the Selector Dial Controlling the Components Connected to This Unit Button Names and Functions in Each Position ■DVD/LD position ■DVD MENU position •DVD MENU operations cannot be performed for some DVD players ■VCR position ■CBL/SAT position ■TV position Setting the Manufacturer Code Programming a New Remote Control Function (Learn Feature) Returning to the Factory Setting ZONE Zone 2 Connections SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 Adventure ES *2 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds These programs express an immense sound field and a large surround effect. They also give depth to the sound from the main speakers to recreate the realistic sound of a Dolby Stereo theater SOUND FIELD PROGRAM PARAMETER EDITING What is a sound field Sound Field Program Parameters Changing Parameter Settings P04 ROCK CONCERT Resetting a Parameter to the Factory-setValue Digital Sound Field Parameter Descriptions ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RS.DELAY (right surround delay) TROUBLESHOOTING Page Page ■Tuner ■Remote control SPECIFICATIONS TV CABLE TV SATELLITE TUNER (DSS) VCR DVD PLAYER LD PLAYER CD PLAYER CD RECORDER MD RECORDER TAPE DECK () Page Quick Reference Card AMP/TUN DSP/TUN TAPE/MD (CD-R) DVD/LD DVD MENU VCR CBL/SAT