Hookups
OthersPreparations
Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED:
The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit is in the standby mode.
AC Power Cord
(General, China, and Australia models)
VOLTAGE SELECTOR (General and China models)
G.
VOLTAGE SELECTOR
240
IMPEDANCE SELECTOR
SET BEFORE POWER ON
|
|
|
| FRONT | : 6Ω MIN./SPEAKER |
| |||||
|
|
|
| REAR | : 4Ω MIN./SPEAKER |
| |||||
|
|
|
| REAR CENTER : 4Ω MIN./SPEAKER |
| ||||||
|
|
|
| CENTER | : 4Ω MIN./SPEAKER |
| |||||
|
|
|
| MAIN A OR B | : 4Ω MIN./SPEAKER |
| |||||
|
|
|
| A + B | : 8Ω MIN./SPEAKER |
| |||||
|
|
|
|
|
|
| |||||
|
|
|
| FRONT | : 8Ω MIN./SPEAKER |
|
|
| |||
|
|
|
|
|
|
| |||||
|
|
|
| REAR | : 8Ω MIN./SPEAKER |
|
|
| |||
|
|
|
| REAR CENTER : 8Ω MIN./SPEAKER |
| ||||||
|
|
|
| CENTER | : 8Ω MIN./SPEAKER |
| |||||
|
|
|
| MAIN A OR B | : 8Ω MIN./SPEAKER |
| |||||
|
|
|
| A + B | : 16Ω MIN./SPEAKER |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
IMPEDANCE SELECTOR switch
AC Power Cord
(U.S.A., Canada, and Singapore models only)
AC OUTLETS
R
ER ON
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
IN./SPEAKER
Select the position whose requirements your speaker system meets.
(Upper position)
FRONT EFFECT:
The impedance of each speaker must be 6Ω or higher.
<U.S.A. and Canada models>
REAR:The impedance of each speaker must be 4Ω or higher.
REAR CENTER: The impedance of the speaker must be 4Ω or higher.
<Except for U.S.A. and Canada models>
REAR:The impedance of each speaker must be 6Ω or higher.
REAR CENTER: The impedance of the speaker must be 6Ω or higher. CENTER: The impedance of the speaker must be 4Ω or higher.
MAIN: If you use one pair of main speakers, the impedance of each speaker must be 4Ω or higher.
If you use two pairs of main speakers, the impedance of each speaker must be 8Ω or higher.
(Lower position)
FRONT EFFECT:
The impedance of each speaker must be 8Ω or higher.
REAR: The impedance of each speaker must be 8Ω or higher.
REAR CENTER:
The impedance of the speaker must be 8Ω or higher. CENTER: The impedance of the speaker must be 8Ω or higher.
MAIN: | <Except for Canada model> |
| If you use one pair of main speakers, the impedance of each speaker |
| must be 8Ω or higher. |
| If you use two pairs of main speakers, the impedance of each speaker |
| must be 16Ω or higher. |
<For Canada model only>
The impedance of each speaker must be 8Ω or higher.
■Connecting the AC power cordPlug in this unit to a wall outlet when all connections are complete.
Caution:
•Do not use other AC power cords than the one provided. (U.S.A., Canada, and Singapore models only)
■AC OUTLETSUse these to connect the power cords from your other components to this unit. The power to the switched outlets is controlled by this unit’s STANDBY/ON (SYSTEM POWER or STANDBY on the remote). These outlets will supply power to any connected unit whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to AC OUTLETS is 100 W.
■Voltage selector (General and China models)
The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.
18