Continued from the front

3 Carry out the AUTO SETUP (IntelliBeam)

Carry out the AUTO SETUP to adjust the settings that best match your listening environment

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

6Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

ENHANCER ENTRY MENU

TV/AV

A-EENTER

YSP

10Press ENTER to start the AUTO SETUP procedure, and then

leave the room within 10 seconds.

The following screen appears on the TV. Leave the room within 10 seconds before the AUTO SETUP procedure starts.

ENHANCER

ENTRY

MENU

 

 

AUTO SETUP START

4

Enjoying surround sound

Enjoy TV or DVD digital audio in surround sound.

For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.

Enjoying DVDs in surround sound

Enjoying TV in surround sound

jack on the front panel.

You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam microphone on top of it as shown below.

1

2

3

4

INTELLIBEAM MIC

IntelliBeam microphone (supplied)

Cardboard microphone stand (supplied)

2Set the IntelliBeam microphone at your normal listening position.

DISPLAY

RETURN

7Press and hold AUTO SETUP for

more than 2 seconds.

The menu screen appears on the TV.

If the menu screen does not appear, check the OSD video pin cable (see the connection example on the front page).

PRESET/TUNE SEARCH

MEMORY

AUTO SETUP

 

A-E

 

 

 

 

FM

 

 

PREPARATION & CHECK

 

AUTO

 

Please connect the MIC.

VOL MODE

SLEEP

Please place the MIC at least

SETUP INPUTMODE

 

 

 

1.8m/6ft away from the YSP

 

 

 

unit. The MIC should be set

5BEAM

ST+3BEAM 3BEAM

at ear level when seated.

Measurement takes about 3min.

 

 

 

1

2

3

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

 

 

Will begin in 10sec

A-E

TV/AV

Please leave the room

ENTER

 

 

YSP

**--------

 

 

DISPLAY

RETURN

[RETURN]:Cancel

 

The setup screen automatically changes during the AUTO SETUP procedure.

When the AUTO SETUP procedure is completed, the following screen appears on the TV.

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM

SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up [RETURN]:Do not save set-up

If “ENVIRONMENT CHECK (FAILED) is displayed, see page 42 in the Owner’s Manual and then run the procedure again.

1Select the DVD video input on your TV.

2Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

TV/AV

A-EENTER

YSP

DISPLAY

RETURN

1Select the TV channel using the remote control supplied with your TV.

2Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

TV/AV

A-EENTER

YSP

DISPLAY

RETURN

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be when you are seated.

8Check the following points.

About the IntelliBeam microphone

yHint

• The result may differ depending on the environment.

• If any error occurs, the corresponding error message appears

31) Press DVD on the remote

control of this unit.

3Press TV on the remote control

of this unit.

IntelliBeam microphone

Center height of

this unit

Cardboard

microphone stand More than 1.8 m (6.0 ft)

Upper bound

position of the

microphone

Within 1 m

 

 

(3.3 ft)

 

 

Within 1 m

Center line

 

(3.3 ft)

 

Listening

Cardboard

IntelliBeam

position

microphone

microphone

Lower bound position

 

 

 

Place the IntelliBeam microphone on the extended center line of this unit and 1.8 m (6.0 ft) or more away from it. Also, make sure place the IntelliBeam microphone within 1 m (3.3 ft) upper or lower from the center height of this unit.

•Is the microphone placed on an imaginary center line drawn from this unit?

•Is the microphone placed within 1 m (3.3 ft) upper or lower from the center height of this unit?

•Is the microphone placed more than 1.8 m (6.0 ft) from the

front of this unit?

About the room environment

• Is your listening room kept as quiet as possible?

on the screen. In this case, see “Error messages for AUTO

SETUP” on page 43 in the Owner’s Manual and then follow

the instructions. To start the AUTO SETUP procedure once

again, press RETURN.

11Press ENTER.

The following screen appears on the TV for 2 seconds and then the menu screen disappears from the TV.

This unit switches to the DVD playback mode.

DVD AUX1 AUX2 AUX3

INPUT1 TV MACRO

STB TV

PRESET/TUNE SEARCH MEMORY

2)Play back the supplied demonstration DVD on the DVD player.

This unit switches to the TV playback mode.

DVD AUX1 AUX2 AUX3

INPUT1 TV MACRO

STB TV

PRESET/TUNE SEARCH MEMORY

A-E

FM

AUTO

VOL MODE SETUP INPUTMODE SLEEP

stand

of the microphone

The best setting may not be done if you are in the room. Prepare to leave the room in 10 seconds after pressing ENTER in step 10.

ENHANCER ENTRY MENU

 

 

AUTO SETUP COMPLETE

 

TV/AV

Please remove the MIC from

 

the YSP and the listening

A-E

ENTER

 

YSP

position.

4

Input channel indicators

Check the digital signal being output at this unit.

 

The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they switch

 

according to the channel composition of the corresponding input source. If the sound is output from your TV

 

speakers, mute the volume on your TV. For details about digital audio input signals, see page 58 in the Owner’s

3Press STANDBY/ON on the

remote control.

The power of this unit turns on.

4

Turn on the power of your TV.

yHint

• When leaving the room, bring this guide with you.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes about 3 minutes.

DISPLAY

RETURN

Manual.

 

VOLUME CH

TV VOL

Before operations, insert batteries into the remote control (see page 32 in the Owner’s Manual).

If necessary, adjust the volume level of this unit.

If you have connected the subwoofer, set the volume and crossover/high cut frequency. Refer to the note on page 38 in the Owner’s Manual.

Subwoofer

 

 

 

 

VOLUME

CROSSOVER/

STANDBY/ON

 

POWER

POWER

 

 

HIGH CUT

 

 

 

 

 

 

 

TV

AV

 

 

 

 

DVD

AUX1

AUX2

AUX3

MIN

MAX

MIN

MAX

 

 

TV

 

 

 

 

 

5

Select the appropriate video input on your TV.

If the OSD video pin cable is connected to the video input 1 on the TV as shown in the connection example, switch the video input to “1”.

• To cancel the AUTO SETUP procedure after it is started,

press RETURN.

12Disconnect the IntelliBeam

microphone.

The AUTO SETUP has completed. Keep the IntelliBeam microphone in a safe place.

The settings are automatically saved in the system memory.

INTELLIBEAM MIC

5Press VOLUME +/- on the remote control to adjust the volume level of this unit.

6Press one of the beam mode buttons on the remote control

to select the desired beam mode.

Select one of the six beam modes that best matches the current input source of this unit. For further information on the beam modes, see page 56 in the Owner’s Manual.

MUTE

TV INPUT

TV MUTE

5BEAM

ST+3BEAM

3BEAM

1

2

3

STEREO

MY BEAM

MY SUR.

4

5

6

To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,

sound beams, etc., see “MANUAL SETUP” on page 76 in the Owner’s Manual.