Bottom Duct Openings from Above | York 150, 120 guide

035-17311-002-A-0803

.

32-11/16

					6-13/16


					Supply		6-13/16
6-13/16					Supply		6-13/16
					Air
					Return
					Air

24

LEFT27-1/2

21

18

21-3/16

19-3/16

17-3/16

12-15/16

7-1/8

							FRONT
	14-						FRONT
	14-
	23/32
						Bottom		Bottom	Bottom Gas
		16-3/8				Condensate		Power, Control	Supply Entry
		16-3/8				Entry		and
						Entry		and
								Convenience
		18-1/16						Convenience
		18-1/16						Outlet Wiring
								Outlet Wiring
								Entries
		19-5/8
		19-5/8

							63-1/2
							63-1/2

FIGURE 9 - BOTTOM DUCT OPENINGS (FROM ABOVE)

DotPlugs 18-1/4

	Return	28-1/4
	Air
	Supply
	Air
18-1/4	PatchPlate
	ForSlide-Out	18-1/16
	DrainPan	18-1/16
	DrainPan
	2-31/32
5-5/32	28-1/4
	28-1/4
	31-11/16

FIGURE 10 - REAR DUCT DIMENSIONS

14	Unitary Products Group

Image 14

York 150, 120 installation manual Bottom Duct Openings from Above

Contents

Installation Manual Table of Contents List of Figures List of Tables Inspection Safety ConsiderationsGeneral Reference ½ 12½ Ton Predator Model Number Nomenclature Nomenclature NOMENCLATURE, Additonal Options Johnson UNT Controller, DFS, APS & Phase Monitor Technicoat Condenser Coil, Phase Monitor, & Coil Guard Preceding Installation InstallationInstallation Safety Information Rigging and Handling Unit Temperature LimitationsLocation Point Load Weight Length of Forks Must be a Minimum of 60 Inches Unit Dimensions Unit Clearances Detail C Bottom Duct Openings from Above Ductwork Duct Covers Side Panels with Hole Plugs Condensate Drain Power and Control Wiring Thermostat WiringControl Wire Sizes Power Wiring Detail Electronic Thermostat Field Wiring RLA LRA FLA Electrical Data DM120 10 TON with Power Convenience Outlet 380 11.5 75.0 Minimum Supply AIR CFM OPTIONS/ACCESSORIESPhysical Data Enthalpy SET Point Adjustment Power ExhaustMinimum Position Adjustment Economizer Enthalpy SET Point Chart Supply AIR Limitations PhasingBlower Rotation Belt Tension 1/2 TON Standard Motor Down Shot Blower PERFORMANCE* † 1/2 TON Optional Motor Down Shot Blower PERFORMANCE* † 10 TON Standard Motor Down Shot Blower PERFORMANCE* † 10 TON Optional Motor Down Shot Blower PERFORMANCE* † 12-1/2 TON Standard Motor Down Shot Blower PERFORMANCE* † 12-1/2 TON Optional Motor Down Shot Blower PERFORMANCE* † 1/2 TON Standard Motor Side Shot Blower PERFORMANCE* † 1/2 TON Optional Motor Side Shot Blower PERFORMANCE* † 4965 12-1/2 TON Standard Motor Side Shot Blower PERFORMANCE* † 12-1/2 TON Optional Motor Side Shot Blower PERFORMANCE* † Checking AIR Quantity Indoor Blower SpecificationsAIR Balance Method ONE Method TWO DRY Coil Delta P Supply AIR Drive Adjustment Motor Sheave Datum Diameters OperationAdditional Static Resistance Sequence of Operations Overview Cooling Sequence of Operation Safety Controls Compressor Protection Electric Heating Sequence of Operations Electric Heating Operation ErrorsElectric Heat Limit Setting Electric Heat Antictpator Setpoints START-UP Cooling Charging the Unit 10 TON Standard Efficiency Superheat Charging 12.5 TON Standard Efficiency Superheat Charging Predator Flash Codes Normal Maintenance TroubleshootingGeneral Basic Troubleshooting Flowchart Unit Control Board Flash Codes Cooling Troubleshooting Guide Unitary Products Group 035-17311-002-A-0803 Unitary 5005 Norman Products York Group Drive 73069