Manuals / Brands / Computer Equipment / Switch / ZyXEL Communications / Computer Equipment / Switch

ZyXEL Communications AES-100 IP Commands, 10.1Setting the IP Address, Chapter

1 90

Download 90 pages, 975.34 Kb

AES-100 User’s Guide

Chapter 10

IP Commands

This chapter shows you how to configure the IP (Internet Protocol) parameters. The IP host implementation in the AES-100 allows you to manage it over the network.

More often than not, you have more than one AES-100 for a particular installation. Before you start configuring the AES-100s, make sure that you

1.Plan ahead.

2.Have a complete diagram showing the whole network.

3.Record the IP parameters assigned to the equipment in your network.

10.1Setting the IP Address

To set the IP address, default gateway and the subnet mask of the Ethernet port of a ADSL Networking Module, use the following command sequence.

1.192.168.1.1> ip

2.192.168.1.1 ip> device delete ether

3.<mac address> ip> device add ether ether //bridge <new ip address>

4.<new ip address> ip> route delete default

5.<new ip address> ip> route add default 0.0.0.0 <default gateway> 00:00:00:00

6.<new ip address> ip> config save

where
<mac address>	=	The MAC address of the ADSL Networking Module.
<new ip address>	=	The IP address you want to configure into the ADSL Networking
		Module.
<default gateway> =		The default gateway IP address of the ADSL Networking Module.
Line 1 brings you to the IP subsystem.

Line 2 clears the old parameters of the AES-100.

Line 3 allows you to add a new IP address for the AES-100. The MAC address of the AES-100 is displayed in the command prompt. The system will automatically compute the subnet mask when the system is restarted. If you want to specify a subnet manually, add the following two commands before line 4:

192.168.1.1 ip> subnet delete ether.home

192.168.1.1 ip> subnet add ether.home ether <subnet address> <subnet mask>

where <subnet mask> is the subnet mask in hexadecimal, for example “ff:ff:ff:00”. Line 4 deletes the existing default route.

Line 5 adds the new default route. The default route tells the system where the gateway (next hop) is when the AES-100 sends frames to a destination that is not on the same subnet as the AES-100.

Line 6 saves the new configuration to the nonvolatile memory.

IP Commands

10-1

Contents

User’s Guide Copyright Disclaimer Trademarks ZyXEL Limited Warranty Interference Statements and Warnings FCC CE Mark Warning: Taiwanese BCIQ A Warning: Certifications Customer Support Contacting Customer Support Table of Contents Page Page List of Figures List of Tables Preface About the AES-100 General Syntax Conventions Related Documentation Page Getting to Know the AES-100 1.1Features Two-SlotChassis 8-PortADSL to Ethernet Multiplexer Modules Integrated Splitters IEEE 802.1Q Tagged VLAN IEEE 802.1p Priority Fast Mode MAC (Media Access Control) Filtering Secured Host 1.2Benefits 1.2.1MTU Application 1.2.2ISP Application 1.2.3Compact Design for Limited Space 1.2.4Scalable Platform for Future Expansion 1.3Physical Specifications Physical Interfaces Dimensions Weight Power Consumption Operating Environment Storage Environment Page Hardware Overview 2.1Unpacking the AES-100 2.2Additional Installation Requirements 2.3Front Panel 2.3.1Front Panel Ports 2.4Console Port 2.5ADSL Port Connections USER 2.6Rear Panel Figure 2-4Connecting the Power Cord to the AES-100and a Power Source Factory Default Settings 3.1IP Parameters 3.2Console Port 3.3SNMP Community Strings 3.4Console, Telnet and FTP Password 3.6Ethernet Port 3.7Other Factory Defaults System Commands 4.1Command Line Interface (CI) 4.2Console Connection 4.3Command Structure 4.3.1Help Facility 4.4Commonly Used Commands 4.4.1Uptime Command 4.4.2Version Command 4.4.3Restart Command 4.4.4Passwd Command 4.5Sys Commands 4.5.1Info Command 4.5.2Set Name Command 4.5.3Set Contact Command 4.5.4Set Location Command 4.6Secured Host Commands 4.6.1Secured Host Command 4.6.2Secured Host Add Command 4.6.3Secured Host Delete Command 4.7UNIX Syslog Commands 4.7.1Syslog Command 4.7.2Syslog Facility Command 4.7.3Syslog Server Command 4.8System Error Log Commands 4.8.1Errlog Display Command 4.8.2Errlog Clear Command 4.8.3Saving and Viewing a Previous Error Log Page ADSL Configuration 5.1ADSL Standards 5.2Profiles 5.3Configured Vs. Actual Rate 5.4Default Settings 5.4.1Default Profile Settings 5.4.2Other Default Settings 5.5ADSL Commands 5.5.1Config Save Command 5.5.2Disable Port Command 5.5.3Disable Ports Command 5.5.4Enable Port Command 5.5.6Linedata Command 5.5.7Lineinfo Command 5.5.8Lineperf Command 5.5.9Linerate Command 5.5.10 List Port Command 5.5.11 List Ports Command 5.5.12 Set Profile Command 5.5.13 Delete Profile Command 5.5.14 List Profiles Command 5.5.15 Show Profile Command 5.5.16 Show Profiles Command 5.5.17 Set Port Command 5.5.18 Set Ports Command 5.5.19 Show Port Command 5.5.20 Show Ports Command 5.5.21 Set PVC Command 5.5.22 Set PVCs Command 5.5.23 Show PVC Command 5.5.24 Show PVCs command Chapter 6 10/100M Fast Ethernet Port Commands 6.110/100M Auto-SensingEthernet 6.2Ethernet Commands 6.2.1Set Auto Command Set Duplex Command 6.2.4Status Command Bridge Commands 7.1Bridge Port Numbers 7.2Basic Commands 7.2.1Config Save Command 7.2.2Device Command 7.3MACfilter Commands 7.3.1MACfilter Command 7.3.2Macfilter Enable Command 7.3.3Macfilter Disable Command 7.3.4Macfilter Add Command 7.4Filter Commands 7.4.1Filter Command 7.4.2A Note about IGMP Snooping 7.4.3Mfilter Command 7.4.4Filterage Command 7.4.5Flush Command 7.4.6Info Command 7.5Port-BasedVLAN Commands 7.5.1Portfilter Command Figure 7-2Example of Modified VLAN Port 7.6Tagged Ethernet Frames Commands (Fast Mode) 7.6.1PVID Command Table 7-1Physical Ports, Port Numbers and AES-100Default PVID Tags in Fast Mode Page Chapter 8 IEEE 802.1Q Tagged VLAN Commands 8.1Introduction 8.2IEEE 802.1Q Tagged VLAN -Tags 8.3VLAN-Aware/VLAN-UnawareDevices 8.4Filtering Databases 8.5IEEE 802.1Q Tagged VLAN Commands 8.5.1Enabling the IEEE 802.1Q Tagged VLAN 8.5.2Disabling the IEEE 802.1Q Tagged VLAN 8.5.3PVID Command 8.5.4SVLAN CPU Command 8.5.5SVLAN List Command 8.5.6SVLAN Setentry Command Modify a Static VLAN Table Example Forwarding Process Example 8.5.7SVLAN Getentry Command Display a Static VLAN Table Entry Example 8.5.8SVLAN Delentry Command Delete a Static VLAN Entry Example 8.5.9DVLAN List Command 8.5.10 DVLAN Getentry Command Display a Dynamic VLAN Table Entry Example 8.5.11 VLAN List Command Figure 8-8Example: VLAN List Command Display IEEE 802.1p Priority Commands 9.1Introduction 9.2IEEE 802.1p Priority Commands 9.2.1Priority Port Command 9.2.2Regen Port Command Page IP Commands 10.1Setting the IP Address 10.2General IP Commands 10.2.1 Config Command 10.2.2 Version Command 10.2.3 Ping Command 10.2.4 Statistics Command Page Remote Management 11.1Management by Telnet 11.2SNMP Management 11.2.1 Supported MIBs 11.3SNMP Access Configuration 11.3.1 SNMP Access Read/Write Command 11.3.2 SNMP Access Delete Command 11.3.3 SNMP Access Flush Command 11.3.4 SNMP Access List Command 11.4SNMP Trap Configuration 11.4.1 Supported Traps 11.4.2 Trap Add Command 11.4.3 Trap Delete Command 11.4.4 Trap Flush Command 11.4.5 Trap List Command Configuration Backup/Restore 12.1Configuration Files of the ADSL Networking Module 12.2Configuration Backup 12.3Configuration Restore Page Firmware Upload and Recovery 13.1FTP Firmware Upload on the ADSL Networking Module 13.2BOOTP/TFTP Firmware Recovery of the ADSL Networking Module Figure 13-1BOOTP/TFTP Server Input Box Figure 13-2Input MAC Update Database Figure 13-3Database Edit Dialog Normal Bootp Figure 13-4Enable BOOTP/TFTP Figure 13-5Enter Debug Mode Page Page Troubleshooting 14.1ADSL LED(s) 14.2Data Transmission 14.3ADSL LED(s) turn On and Off 14.4Data Rate 14.5Configured Settings 14.6Password 14.7Remote Server 14.8SNMP 14.9Telnet Index