ZyXEL Communications 1111, 2110, 3110, SHD1110 2.1.3 Z-Wave’sConfiguration

Chapter 2 SHD1110 Programming

When the SHD1110 is triggered, it will send out BASIC_SET_COMMAND to the nodes of Grouping 2.

[Command Class Basic, Basic Set, Value = (255)0xFF] send trigger-ON command

[Command Class Basic, Basic Set, Value = 0(0x00)] send trigger-OFF command

Refer to the Z-Wave’s Configuration section to configuration parameter 1 for the setting of basic set command.

2.1.3 Z-Wave’s Configuration

The table below lists the configuration parameters and the value range for users to set up the SHD1110.

Table 1 Z-Wave Configuration Table

	PARAMETER	FUNCTION	SIZE (BYTE)	VALUE	UNIT	FACTORY	DESCRIPTION
	PARAMETER	FUNCTION	SIZE (BYTE)	VALUE	UNIT	DEFAULT	DESCRIPTION
						DEFAULT
	1	Basic Set	1	0~99	% of	99 / 99	Set basic set value to
		Level			Brightness		be on (or Dim Level)
					(Dimmer		/off.
					Level)		/off.
					Level)
							0: Disable

	2	Temperature	1	-20~50	Degree	30 / 99	Set temp.trigger-ON
		Trigger-ON		or			value to be _ degree.
		Value		99			99: Clear Temp.
							99: Clear Temp.
							trigger-ON value

	3	Temperature	1	-20~50	Degree	20 / 99	Set temp.trigger-OFF
		Trigger-OFF		or			value to be _ degree.
		Value		99			99: Clear Temp.
							99: Clear Temp.
							trigger-OFF value

	4	Humidity	1	20~90	%	50 / 99	Set humid. trigger-
		Trigger-ON		or			ON value to be _%.
		Value		99			99: Clear Humid.
							99: Clear Humid.
							trigger-ON value

	5	Humidity	1	20~90	%	40 / 99	Set humid. trigger-
		Triger-OFF		or			OFF value to be _%.
		Value		99			99: Clear Humid.
							99: Clear Humid.
							trigger-OFF value

	6	Auto Report	2	1~1439	Minute	0 / 0	Set auto report time
		(Time		or			interval to be _ mins.
		Interval)		99			0: Disable auto
							0: Disable auto
							report

10
10	Z-Wave Series Programming Guide

Contents

www.zyxel.com Page About This User's Guide Intended Audience Related Documentation Document Conventions Warnings and Notes Safety Warnings Table of Contents Page The Z-WaveSeries 1.1 Overview SHD1110 Programming 2.1 Z-WaveGroups (Association Command Class Version 2) 2.1.1 Grouping 2.1.1.1 POWER_APPLIED command 2.1.1.2 MULTILEVEL_SENSOR_REPORT 2.1.2 Grouping 2.1.3 Z-Wave’sConfiguration 2.1.4 Auto Report 2.1.4.1 Time Interval 2.1.4.2 Temperature Change 2.1.4.3 Humidity Change 2.1.5 Wakeup Configuration 2.1.5.1 Wakeup Time Interval 2.1.5.2 Sleep Time Interval 2.1.6 Command Classes SHD1111 Programming 3.1 Z-WaveGroup (Association Command Class Version 2) 3.1.1 Tamper Event Report (Alarm Report) 3.1.2 Control other Z-WaveDevices 3.1.3 Z-Wave’sConfiguration 3.2 Advanced Programming 3.2.1 Battery Check Command 3.2.2 Wakeup Command Class 3.2.3 Command Classes SHD2110/3110 Programming 4.1 Basic Command Class / Binary Switch Command Class 4.1.1 BASIC_GET / BINARY_SWITCH_GET 4.1.2 BASIC_SET / SWITCH_BINARY_SET 4.2 Z-WaveGroups (Association Command Class Version 2) 4.2.1 Grouping 4.2.1.1 POWER_APPLIED command 4.2.1.2 On/Off Event Report (True State) 4.2.1.3 Binary Switch Report Command 4.2.2 Grouping 4.2.2.1 Control Other Z-WaveDevices (Basic Set) 4.2.3 Z-Wave’sConfiguration 4.2.3.1 The True Period 4.2.3.2 Send Basic Command to Grouping 4.2.4 Meter Command Class 4.2.4.1 Instant Power Consumption of Module 4.2.4.2 Accumulated Power Consumption (KW/h) 4.2.4.3 Clearing Accumulated Power Consumption 4.2.5 Command Classes Legal Information Copyright Disclaimers Trademarks Federal Communications Commission (FCC) Interference Statement Notices Viewing Certifications ZyXEL Limited Warranty Note Registration