Lincoln Electric SVM192-A service manual Engine Adjustments

Page 30

TOC

TOC

D-4

MAINTENANCE

D-4

ENGINE ADJUSTMENTS

 

WARNING

 

 

Return to Section

Return to Section TOC

Return to Master

Return to Master TOC

WARNING

OVERSPEED IS HAZARDOUS

The maximum allowable high idle speed for this machine is 3750 RPM, no load. Do NOT tamper with governor components or setting or make any other adjustments to increase the maximum speed. Severe personal injury and damage to the machine can result if operated at speeds above maximum.

------------------------------------------------------------------------

Adjustments to the engine are to be made only by a Lincoln Service Center or an authorized Field Service Shop.

SLIP RINGS

A slight amount of darkening and wear of the slip rings and brushes is normal. Brushes should be inspected when a general overhaul is necessary.If brushes are to be replaced, clean slip rings with a fine emery paper.

CAUTION

Do not attempt to polish slip rings while engine is running.

------------------------------------------------------------------------

HARDWARE

Both English and Metric fasteners are used in this welder.

GASES FROM BATTERY can explode.

• Keep sparks, flame and cigarettes away from battery.

To prevent EXPLOSION when:

•INSTALLING A NEW BATTERY - disconnect negative cable from old battery first and connect to new battery last.

•CONNECTING A BATTERY CHARGER - Remove bat-

tery from welder by disconnecting negative cable first, then positive cable and battery clamp. When rein- stalling, connect negative cable last. Keep well venti- lated.

•USING A BOOSTER - connect positive lead to bat- tery first then connect negative lead to engine foot.

BATTERY ACID CAN BURN EYES AND SKIN.

• Wear gloves and eye protection and be careful when working near battery. Follow instructions printed on battery.

BATTERY

1.When replacing, jumping, or otherwise connecting the battery to the battery cables, the proper polarity must be observed. Failure to observe the proper polarity could result in damage to the charging circuit. The positive (+) battery cable has a red terminal cover.

2.If the battery requires charging from an external charger, disconnect the negative battery cable first and then the positive battery cable before attaching the charger leads. Failure to do so can result in damage to the internal charger components. When reconnecting the cables, connect the positive cable first and the negative cable last.

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

ENGINE MAINTENANCE PARTS

 

 

KOHLER C23S

 

 

 

 

 

KOHLER 12 050 01

 

Oil Filter

FRAM PH8172*

 

 

 

 

Air Filter

KOHLER 47 083 03

 

Element

FRAM CA79

 

 

 

 

Air Filter

KOHLER 24 083 02

 

Pre-Cleaner

 

 

 

 

 

Fuel Filter

KOHLER 24 050 10

 

 

 

 

Spark Plugs

CHAMPION RC12YC

 

(Resistor

(.030” GAP)

 

Type)

 

 

 

 

*Oil capacity increases from 2.0 Qts. to 2.1 Qts. when using this filter.

EAGLE™ 10,000

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Eagle 10,000 ISAFETYi Eagle 10,000Fumes and Gases SafetyElectric Shock can kill ARC Rays can burn Can be dangerousCylinder may explode Powered equipmentWelding Cutting Sparks can cause fire or If damaged ExplosionPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications Eagle 10,000 K2343-1,K2343-2Height Width Depth Weight Spark Arrester Safety PrecautionsMachine Grounding TowingFollow vehicle manufacturer’s instructions Vehicle MountingFuel Gasoline Fuel only Do not overfill tank, fuel expansion may cause overflowLifting Additional Safety Precautions High Altitude OperationAngle of Operation Location / VentilationInstructions Connection of Lincoln Electric Wire FeedersAdditional Safety Precautions Welder OperationDuplex Receptacles Auxiliary Power120/240 Volt Dual Voltage Receptacle Motor StartingAdditional Resistive Electrical Device USE with the Eagle 10,000These Devices Without Type LoadsStandby Power Connections Auxiliary Power While WeldingSimultaneous Welding and Power Connection diagram shown Eagle 10,000Connection of Eagle 10,000 to Premises Wiring Figure A.1Table of Contents Operation Section General Description Engine SwitchOperation Welder Controls Function and OperationEagle 10,000 Approximate Fuel Consumption Range SwitchOPERATIONB-3 Control DialStarting the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Stopping the EngineTIG Constant Current Welding Wire Feed Welding ProcessesWelding Process ARC GougingTypical Current Ranges 1 for Tungsten ELECTRODES2 Summary of Welding ProcessesTable of Contents Accessories Section Accessories Optional Equipment Field InstalledK1745-1 GAS Cylinder Holder Plasma Cutting Stick Wire FeedRecommended Equipment TIG WeldingEagle 10,000 Table of Contents Maintenance Section Engine OIL Change MaintenanceSafety Precautions Engine OIL Refill CapacitiesAIR Cleaner and Other Maintenance OIL Filter ChangeEngine Adjustments Figure D.1 Major Component Locations Eagle 10,000 1TABLE of CONTENTS-THEORY of Operation Section E-1 BATTERY, STARTER, ENGINE, ROTOR, STATOR, and Idler Solenoid Theory of OperationRotor Field Feedback Auxiliary Power Figure E.3 Rotor Field Feedback and Auxiliary PowerWeld WINDING, REACTOR, and Range Switch Output BRIDGE, CHOKE, and Output Terminals1TABLE of Contents Troubleshooting and Repair F-1 2TROUBLESHOOTING and REPAIRF-2 HOW to USE Troubleshooting GuideTroubleshooting and Repair PC Board Troubleshooting ProceduresPerform the Rotor Voltage Test Problems Possible Areas Symptoms Misadjustments Recommended Course of ActionProblems Symptoms Possible Areas MisadjustmentsRotor Voltage2. PTestrform Engine Problems Wiring Charging Circuit Test BridgePerformTestthe. Output Rectifier Eagle 10,000 Rotor Voltage Test Test DescriptionMaterials Needed Test Procedure Remove the case top, then reinstall the fuel capRotor Voltage Test Rotor Resistance Test Rotor Resistance Test Remove the case top, then replace the fuel capTroubleshooting and Repair Eagle 10,000 Auxiliary and Field Winding Test Auxiliary and Field Winding Test To test the 115 VAC windingTo test the 230 VAC winding To test the field winding Eagle 10,000 Output Rectifier Bridge Test Output Rectifier Bridge Test Figure F.4 Location of Output Rectifier LeadsCharging Circuit Test Charging Circuit Test Figure F.5 Location of Voltage RegulatorEngine Throttle Adjustment Test Engine Throttle Adjustment Test Strobe-tach MethodFigure F.7 Frequency Counter MethodEngine Throttle Adjustment Test Oscilloscope Method Vibratach MethodScope Settings Normal Open Circuit Voltage Waveform 115VAC SupplyHigh Idle no Load Output Control AT Maximum Typical DC Weld Output Waveform CC Mode Machine LoadedMachine Loaded to 200 Amps AT 26 VDC Abnormal Open Circuit DC Weld Voltage Waveform Normal Open Circuit DC Weld Voltage Waveform CC Mode Brush Removal and Replacement Brush Removal and Replacement ProcedureSlip Rings Figure F.9 Brush LEADS/BRUSHES Retained with Cable TIEEagle 10,000 Printed Circuit Board Removal Replacement Replacement Printed Circuit Board RemovalTroubleshooting and Repair Eagle 10,000 43TROUBLESHOOTING and REPAIRF-43 Output Rectifier Bridge Removal Replacement44TROUBLESHOOTING and REPAIRF-44 Output Rectifier Bridge Removal45TROUBLESHOOTING and REPAIRF-45 Eagle 10,000 ENGINE/ROTOR Removal and Replacement InstructionsENGINE/ROTOR Removal and Replacement Figure F.12 Component LOCATIONS, ENGINE/ROTOR RemovalEngine and Rotor Removal Procedure Rotor Removal Procedure Figure F.13 Engine and Rotor Removed from Stator THRU-BOLTReplacement KIT S20788 Reassembly ProcedureENGINE/ROTOR Removal Engine Output Auxiliary Power Receptacle OUTPUT1Retest After Repair Welder DC OUTPUT1Table of Contents Diagram Section Electrical Diagrams Eagle 10,000 KohlerWiring Diagram Code 11397 M21271 Schematic Complete Machine Code 11096 L12259 TerminalSchematic Complete Machine Code 11397 L13104 Torroid Core located onSchematic IDLER/FIELD Control P.C. Board L12197

SVM192-A specifications

Lincoln Electric's SVM192-A is a standout model in the sphere of welding machines, renowned for its advanced technology and versatility, making it a preferred choice among welding professionals and industrial applications. This single-phase inverter-based machine balances performance and portability, providing users with a reliable solution for a variety of welding tasks.

One of the key features of the SVM192-A is its capacity to perform multiple welding processes. It supports MIG, TIG, and stick welding, which allows users to switch between different techniques depending on the project requirements. This multi-functionality enhances the machine's utility, making it viable for various applications ranging from home projects to professional fabrication works.

The SVM192-A is equipped with Lincoln Electric’s proprietary technologies, including the advanced inverter technology, which ensures high efficiency and power output while maintaining a compact size. This inverter technology not only improves arc stability but also reduces power consumption and heat generation, making it a more eco-friendly option.

Key characteristics of the SVM192-A include a user-friendly digital display that provides clear settings for amperage, voltage, and other parameters, enabling precise control during welding. The machine also features a robust construction, designed to withstand tough working environments, ensuring longevity and minimal downtime.

Moreover, the SVM192-A incorporates safety features designed to protect the user and the machine, including overcurrent and thermal overload protection. This prioritization of safety ensures a worry-free operation, allowing welders to focus on their craft without the distraction of potential hazards.

Portability is another significant advantage of the SVM192-A. Weighing in at a lightweight design, it is easy to transport, making it ideal for mobile operations or jobs that require moving the equipment frequently.

In summary, the Lincoln Electric SVM192-A embodies versatility, efficiency, and durability, making it an exceptional choice for both novice and experienced welders. Its ability to handle multiple welding processes, combined with advanced technologies and user-friendly features, positions it as a top contender in the welding equipment market, suitable for a wide range of applications in various sectors.
Top Page Image Contents