Ryobi RY09701 Charging the Battery Pack, Charging a HOT Battery Pack, To install Battery Pack

Page 12

OPERATION

CAUTION:

If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest service center for service or replacement.

CHARGING THE BATTERY PACK

See Figure 7.

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge overnight prior to use.

Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged.

Charge battery pack only with the charging assembly provided.

Make sure power supply is normal household voltage, 120 V, AC only, 60 Hz.

Connect charger to power supply.

Place battery pack in charging stand. Align raised rib on battery pack with groove in charging stand.

Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging stand.

The charge indicator light (LED), located on the charging stand, will light up red and glow when the charger is properly connected to power supply. This light indicates the charger is operating properly. It will remain on until battery pack is removed from charging stand or charger is disconnected from power supply.

After normal usage, 3 hours or less of charging time is required to fully recharge battery pack.

If both red and orange LED indicators glow, the battery pack is deeply or completely discharged, and 6 hours or longer of charging time is required to fully recharge battery pack.

NOTE:  If charger does not charge battery pack or orange LED continues to glow after more than 30 minutes of charging, return battery pack and charging assembly to your nearest Ryobi Authorized Service Center for electrical check.

The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature.

When batteries become fully charged, unplug charger from power supply and remove the battery pack.

CHARGING A HOT BATTERY PACK

When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge.

NOTE:  This situation only occurs when continuous use of the product causes the batteries to become hot. It does not occur under normal circumstances. Refer to CHARGING THE BATTERY PACK for normal recharging of batteries. If the charging assembly does not charge the battery pack under normal circumstances, return both the battery pack and charging assembly to your nearest Ryobi Authorized Service Center for electrical check.

to install BATTERY PACK

See Figure 8.

Place the battery pack in the product. Align raised rib on battery pack with groove in product’s battery port.

Make sure the latches on each side of the battery pack snap in place and that battery pack is secured in product before beginning operation.

TO REMOVE BATTERY PACK

Locate latches on side of battery pack and depress both sides to release battery pack from the product.

Remove battery pack from the product.

10 — English

Image 12
Contents Save this Manual for Future Reference ALL Versions Toutes LES Versions Todas LAS VersionesVolt battery pile de 12 V, batería de 12 Iii Table of Contents General Safety Rules Model Battery Pack ChargerRead all instructions RY09600, RY09701 130269012 140295003Service RefuelingSymbols Symbol Name ExplanationProduct Specifications Symbol Signal MeaningFeatures AssemblyAdjusting Harness and waist Straps Adjusting Adjustable handleTo adjust harness strap assembly To adjust waist strap assemblyOperation ApplicationsFueling and Refueling the blower Oxygenated FuelsCharging the Battery Pack Charging a HOT Battery PackTo install Battery Pack To Remove Battery PackStarting and Stopping If assistance is required Starting this productOperating the Blower Maintenance Troubleshooting Problem Possible Cause SolutionWarranty This product was manufactured with a catalyst mufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage Règles DE Sécurité Générales AVERTISSEMENT Lire Toutes LES Instructions Modèle Bloc DE Batteries ChargeurRègles DE Sécurité Particulières DépannageRavitaillement en carburant Symboles Symbole NOM ExplicationCaractéristiques Fiche TechniqueAssemblage Assemblage DES Tubes DE Soufflante Réglage DES Sangles DE Harnais ET DE CeintureRéglage DE LA poignée de réglable Voir les figures 3Utilisation AvertissementCarburants Oxygénés Approvisionnement Et CarburantInstallation DU Bloc DE BATTERIES  Charge DU Bloc DE BATTERIES Charge D’UN Bloc DE BATTERIES CHAUD Retrait DU Bloc DE BATTERIES Advertencia Funcionamiento DE LA SopladoraPrecaución Si necesita asistencia llame alEntretien Problème Cause Possible Solution DépannageGarantie Fonctionnement Chaque annéeÉnoncé DE LA Garantie Limitée Responsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Reglas DE Seguridad Generales Lea todas las instruccionesModelo CargadorReglas DE Seguridad Específicas ServicioReabastecimiento de combustible Símbolos Símbolo Nombre Denominación / ExplicaciónPeligro Especificaciones DEL ProductoSímbolo Señal Significado Características ArmadoMontaje DE LOS Tubos DE LA SOPLA- Dora Vea las figuras 3Para ajustar las correas del arnés Para ajustar las correas de la cinturaFuncionamiento Llenado DEL TanqueAplicaciones Combustibles OxigenadosCómo Cargar EL Paquete DE Pilas Cómo Cargar EL Paquete DE Pilas Cuando Está CalientePara Instalar EL Paquete DE Baterías Desmontaje DEL Paquete DE BateríasEn cas de besoin d’assistance Démarrage avec ce produit Utilisation DE LA SoufflantePara DAR Arranque Manual Pour toute assistance, appeler le Mantenimiento Solución DE Problemas Problema Causa Posible SoluciónGarantía 4050Declaración DE LA Garantía Limitada Cobertura DE LA Garantía DEL Fabricante Notas Notas Notas Manuel D’UTILISATION / Manual DEL Operador Soufflante Dorsale / SOPLADORA DE MochilaCalifornia Proposition Proposition 65 DE L’ÉTAT DE Californie

RY09701, RY09600 specifications

The Ryobi RY09600 and RY09701 are two notable additions to Ryobi's diverse line of outdoor power equipment, designed to enhance efficiency and ease of use for homeowners and professionals alike. These models are engineered with cutting-edge technology, focused on delivering performance and durability.

The Ryobi RY09600 is a robust string trimmer, equipped with a powerful 26cc, 2-cycle engine that provides ample power for tackling thick grass, weeds, and light brush. This compact trimmer features a lightweight design, making it easy to maneuver in tight spaces. The RY09600 comes with an automatic feed spool, ensuring a consistent cutting line length without the need for manual adjustments. Additionally, it features a comfort grip handle that reduces vibration and increases control, allowing for extended use without fatigue.

On the other hand, the Ryobi RY09701 is a versatile, gas-powered blower that boasts a powerful 26cc engine, designed for both professionals and DIY enthusiasts. This blower is capable of delivering air speeds of up to 150 mph, effectively clearing leaves, debris, and grass clippings from various surfaces. The RY09701 features a lightweight design, which minimizes strain during prolonged use. An adjustable speed trigger allows for tailored airflow control, providing the user with the flexibility to manage different tasks efficiently. The blower's ergonomic handle ensures comfort, making it easier to navigate around gardens and driveways.

Both models benefit from Ryobi’s commitment to innovation, utilizing advanced technologies such as Easy Start, which simplifies the starting process. This feature is particularly advantageous for users who may struggle with traditional starting mechanisms. Furthermore, their construction includes durable components, ensuring longevity even under rigorous use.

In summary, the Ryobi RY09600 and RY09701 are exemplary tools for any outdoor maintenance task, combining power, ease of use, and user-friendly designs. With their high-performance engines, thoughtful features, and ergonomic designs, these tools offer exceptional value, making yard work simpler and more efficient. Whether used for trimming or blowing, these models reflect Ryobi’s dedication to providing quality equipment for outdoor enthusiasts.