Scag Power Equipment SWZV manual Limited Warranty - Commercial Equipment

Page 64

LIMITED WARRANTY - COMMERCIAL EQUIPMENT

Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judg- ment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor during the periods specified below. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service Dealer.

This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workmanship:

*Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.

*Batteries are covered for ninety (90) days.

*Frame and structural components including oil reservoir and oil coolers are warranted for 2 years (Parts and labor).

*Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st and 2nd year; parts only 3rd year) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request components for evaluation. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.

*Engines and electric starters are covered by the engine manufacturer’s warranty period.

*Major drive system components are warranted for two (2) years by Scag Power Equipment. (Parts and labor) (Two year warranty exclude fittings, hoses, drive belts). The repair or replacement of the hydraulic pump or hydraulic motor will be at the option of Scag Power Equipment. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.

*Electric clutches have a Limited Warranty for 2 years (parts and labor).

*Spindle Assemblies have a Limited Warranty for three years (parts and labor 1st and 2nd year; parts only 3rd year).

*Any Scag product used for rental purposes is covered by a 90 day warranty.

The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.

This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual. The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its opera- tion, performance or durability.

Scag Power Equipment reserves the right to change or improve the design of any mower without assuming

any obligation to modify any mower previously manufactured. All other implied warranties are limited in duration to the two (2) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate two year or ninety day warranty period. Scag’s obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Image 64
Contents OPERATOR’S MANUAL MODEL SWZVwith a serial number of D4000001 to D4099999 with a serial number of D4100001 to D4199999D4200001 to D4299999 E2700001 to E2799999TABLE OF CONTENTS Section 2 - Safety InformationSUBJECT PAGETABLE OF CONTENTS CONTD GENERAL INFORMATION USE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES1.1 INTRODUCTION 1.2 DIRECTION REFERENCEISO Symbols CE MarkFast SlowSAFETY INFORMATION 2.2 SIGNAL WORDSThis symbol means “Attention! Become Alert! Your Signal Word2.4 OPERATION CONSIDERATIONS 2.4 OPERATION CONSIDERATIONS CONTD 2.5 MAINTENANCE CONSIDERATIONS & STORAGE 2008 SWZV Safety Decals 2.6 SAFETY AND INSTRUCTIONAL DECALS483402 483397 483406 482291 483608 SPECIFICATIONS ENGINESENGINE DECK DRIVE SYSTEMADDITIONAL SPECIFICATIONS APPROXIMATE DIMENSIONSCUTTER DECKS OPTIONAL ITEMS/ATTACHMENTSSection OPERATING INSTRUCTIONS4.1 CONTROLS AND INSTRUMENT IDENTIFICATION 4.2 SAFETY INTERLOCK SYSTEM 4.4 STARTING THE ENGINE4.5 GROUND TRAVEL AND STEERING Forward TravelReverse Travel Start practicing with a slow engine speed and slow forward travel4.6 ENGAGING THE DECK DRIVE CUTTER BLADES Figure 4-4 Cutter Engage SwitchFigure 4-3 Steering Controls ROTATING BLADES 4.7 HILLSIDE OPERATION4.8 PARKING THE MOWER 4.10 REMOVING CLOGGED MATERIAL4.11 MOVING MOWER WITH ENGINE STOPPED 4.13 ADJUSTING CUTTING HEIGHT4.12 RECOMMENDATIONS FOR MOWING Section TROUBLESHOOTING CUTTING CONDITIONS CONDITIONCAUSE CURESection TROUBLESHOOTING CONTD the Ground Scalping - BladesADJUSTMENTS 6.1 PARKING BRAKE ADJUSTMENT6.2 TRAVEL ADJUSTMENTS Neutral AdjustmentTracking Adjustment Figure 6-1 RH Drive Wheel AdjustmentFigure 6-2 LH Drive Wheel Adjustment before beginning work6.3 THROTTLE CONTROL AND CHOKE ADJUSTMENTS 6.4 BELT ADJUSTMENT6.6 CUTTER DECK ADJUSTMENTS 6.5 BELT ALIGNMENTCutter Deck Pitch Figure 6-4 Cutter Deck Pitch AdjustmentCutter Deck Height Custom-Cut Baffle Adjustment 3-Position Custom-Cut Baffle Adjustment 7-Position Custom-Cut Baffle AdjustmentFigure 6-10. 7-Position Custom-Cut Baffle Adjustment Figure 6-9. 3-Position Custom-Cut Baffle AdjustmentCustom-Cut Baffle Adjustment MAINTENANCE 7.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALSMAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS CONTD Timken Lithium Multi-Use #2 found at industrial shopsFigure 7.1 Lubrication Fitting Points GREASE FITTING LUBRICATION Lubricant Interval Lithium MP White Grease40 Hours/Weekly Chassis Grease 100 Hours/Bi-weekly Chassis Grease 200 Hours/MonthlyB. Changing Hydraulic Oil 7.3 HYDRAULIC SYSTEM A. Checking Hydraulic Oil LevelFigure 7-2 Hydraulic Oil Reservoir C. Changing Hydraulic Oil Filter Element B. Changing Engine Crankcase OilC. Changing Engine Oil Filter 7.4 ENGINE OIL A. Checking Engine Crankcase Oil Level7.6 ENGINE AIR CLEANER A. Cleaning and/or Replacing Air Cleaner Element7.5 ENGINE FUEL SYSTEM A. Filling the Fuel Tank B. Replacing In-Line Fuel Filter Element7.7 DRIVE BELTS 7.8 CUTTER BLADES A. Blade InspectionB. Blade Sharpening DO NOT sharpen the blades beyond 1/3 of the width of the blade7.10 BODY AND DECK C. Blade Replacement7.9 TIRES Section FRAME Section 36A CUTTER DECKSWZV 36A Cutter Deck Part Description20 FRAME Section 48V & 52V CUTTER DECKSSWZU07 48V,52V Bolt, Hex Head 3/8-16 x 1-1/4” Special Lock Rear To Lift Section 36” CUTTER DECK FRAMEControl 36” CUTTER DECK FRAME Section 48” & 52” CUTTER DECK FRAME 48” & 52” CUTTER DECK FRAME Section CUTTER DECK LIFT LEVER CUTTER DECK LIFT LEVER 3738 Section HANDLE ASSEMBLY69 4 Section HANDLE ASSEMBLY 7 J Section HYDRAULIC AND LOWER BRAKE ASSEMBLY14 H Used Only on Machines Equipped with a 52” Cutter Deck Electric Start Model OnlySection ELECTRICAL SYSTEM AND UPPER BRAKE ASSEMBLY MANUAL START TO CLUTCHSCAG MENTKey Fob w/Keys Ref. Part No. No. DescriptionGrip, Brake POWERSC ENGINECLUTCH 43 44Section ELECTRICAL SYSTEM AND UPPER BRAKE ASSEMBLY ELECTRIC START Section HYDRAULIC PUMP ASSEMBLY PORT ASIDE PORT BHYDRAULIC PUMP ASSEMBLY NumberSection REPLACEMENT DECALS AND INFORMATION PLATES Heavy-Duty CommercialMANUFACTURED UNDER ONE OR MORE PATENTS PENDINGPart ENGINE GROUNDCLUTCH VOLTAGE REGULATORELECTRICAL SCHEMATIC - ELECTRIC START MODULE20 AMP FUSES GROUND STRIPEW/YELLIMITED WARRANTY - COMMERCIAL EQUIPMENT GARANTÍA LIMITADA - EQUIPO COMERCIAL ADVERTENCIA PRECAUCIÓNPLATAFORMA Y CUERPO LLANTASADVERTENCIA cuchilla la de Inspección .ACORTE DE CUCHILLAS cuchillas las de Afilado .Bcombustible de tanque del Llenado .A línea en combustible de filtro del elementos los de Reemplazo .BDEL COMBUSTIBLE DE SISTEMA motor del aceite de filtro de Cambio .C cárter del aceite de Cambio .Bhidráulico cárter del aceite de nivel del Verificación .AHIDRÁULICO SISTEMA hidráulico aceite de Depósito 2-7 Figurapágina próxima la en C sección la en describe se como tal aceite de filtro el cambiar debe31 conexión de puntos de Lubricación 1.7 Figura horas/mensualmente 200 chasis de Grasasemanas dos Horas/cada 100 chasis de Grasa horas/semanalmente 40 2125 MP litio de blanca Grasa27 PÁGINA 1,-7 FIGURA LA VEA GRASA DE CONEXIÓN DE LUBRICACIÓN DE TABLA- LUBRICACIÓNObservaciones ProcedimientoMANTENIMIENTO 7 SecciónRECOMENDADOS SERVICIO DE INTERVALOS - MANTENIMIENTO DE TABLA suciedad o polvo6 Sección montaje de accesorios de Ubicaciónmontaje de Ranura personalizado corte de deflector del Ajusteposiciones 7 de personalizado corte de deflector del Ajusteposiciones 3 de corte de plataforma la de tamaño el con acuerdoADVERTENCIA máquina lade posterior la a frontal parte la de cara dé que modo de corte de cuchilla la Ponga .corte de plataforma lacorte de plataforma la de Altura corte de plataforma la de Inclinaciónla de apropiada altura la verificar Para .indicador el en estas realice También .plataforma la de posteriorADVERTENCIA corte de plataforma la de NivelCORTE DE PLATAFORMA LA DE AJUSTES CORREA LA DE ALINEACIÓNbaja más presión la con lado al tirará máquina PRECAUCIÓNcorrecta es motrices ruedas las en llantas las de ADVERTENCIA AJUSTESPRECAUCIÓN alineación de AjusteCONTINUACIÓN FALLAS DE SOLUCIÓN 5 SecciónSOLUCIÓN CAUSA5 Section CONTINUACIÓN FALLAS DE SOLUCIÓN023 SGB 021 SGBCORTE DE CONDICIONES LAS EN FALLAS DE IDENTIFICACIÓN plataforma4 Section CORTE DE ALTURA LA DE AJUSTEPRECAUCIÓN GIRATORIAS CUCHILLAS4 Sección ADVERTENCIACORTACÉSPED CUESTA UNA EN OPERACIÓNDEL ESTACIONAMIENTO normal es Esto .velocidad adquiereCORTE DE CUCHILLAS PLATAFORMA DE TRANSMISIÓN LA DE CONEXIÓN reversa en Desplazamiento adelante hacia DesplazamientoDIRECCIÓN Y TERRENO EL EN DESPLAZAMIENTOADVERTENCIA MOTOR DEL ARRANQUEhoras 10 aproximadamente o uso de día Primer INICIALOPERACIÓN DE INSTRUCCIONES PRECAUCIÓNIDENTIFICACIÓN INSTRUMENTOS E CONTROLES36A-SWZV APROXIMADAS DIMENSIONES 52V-SWZV48V-SWZV OPCIONALES ARTÍCULOS/ACCESORIOSESPECIFICACIONES TRANSMISIÓN DE SISTEMADecals Safety SWZV 2 SecciónSEGURIDAD DE Y INSTRUCTIVAS CALCOMANÍAS 483608 482291 483406 483397 483407ADVERTENCIA PELIGRO PRECAUCIÓNALMACENAMIENTO Y MANTENIMIENTO DE CONSIDERACIONES OPERACIÓN DE CONSIDERACIONES NOTAde prolongados períodos por máquina esta audición la de pérdida causar puede tiempooperar El .auditivos protectores use Siempre SEGURIDAD DE INFORMACIÓN OPERACIÓN LA A PREVIAS CONSIDERACIONESSEÑALIZACIÓN DE PALABRAS INTRODUCCIÓNoperador del manual el Lea ISO Símbolos GENERAL INFORMACIÓN 1 SecciónTRANSMISIÓN DE TREN DEL COMPONENTES LOS A Y MOTOR AL SERVICIO INSTRUCCIONES DE REFERENCIACONTINUACIÓN CONTENIDO DE TABLA repuesto de Piezas - 8 SecciónMantenimiento - 7 Sección Ajustes - 6 SecciónCONTENIDO DE TABLA 21-19corte de condiciones las en fallas de Identificación - 5 Sección operación de Instrucciones - 4 SecciónADVERTENCIA MANUAL DEL OPERADOR SWZV MODELO