Scag Power Equipment SVR61V-29FX manual Engaging the Deck Drive Cutter Blades

Page 18

R

Section 4

PULL BACK	NEUTRAL PUSH FOR
FOR REVERSE	FORWARD

“N” FOR NEUTRAL LOCK “D” FOR DRIVE

Figure 4-2. Forward / Reverse Controls

4.6ENGAGING THE DECK DRIVE (CUTTER BLADES)

1.Set the throttle at about 3/4 speed. Do not attempt to engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.

2.Engage the deck drive by pulling out on the yellow switch, located on the instrument panel, to the engage position. See Figure 4-4.

WHILE TRAVELING FORWARD, PULL BACK ON LEFT STEERING CONTROL TO STEER LEFT

WHILE TRAVELING FORWARD,PULL BACK

ON RIGHT STEERING CONTROL TO STEER RIGHT

Figure 4-3. Steering Controls

PULL UP TO ENGAGE

PUSH DOWN TO DISENGAGE

390S0138

Figure 4-4. Cutter Engage Switch

CAUTION

Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire are behind the mower.

CAUTION

Before backing up, observe behind the mower for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.

- NOTE -

A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed. This is normal.

14

Image 18

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Following SectionDirection Reference General InformationIntroduction Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation considerations Operation Considerations Slope Angle Graph Maintenance Considerations & storage Front Tie Down PointsUsing a spark arrestor SPARK Ignition SystemSafety and Instructional Decals 483402 483407Electrical SpecificationsEngine Engine DeckWeights and Dimensions SvR-61v Cutter DeckProductivity Operating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and Steering Forward TravelReverse Travel Engaging the Deck Drive Cutter Blades Forward / Reverse ControlsParking the Mower Hillside OperationAfter Operation Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking brake adjustmentTravel adjustment Neutral adjustment Tracking adjustmentCutter deck adjustments Throttle Control and Choke AdjustmentsBelt Adjustments Belt AlignmentCutter deck level Cutter deck pitchCutter Deck Height Adjustment Cutter deck heightCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected Electric clutch adjustment FrONT Weight AdjustmentOperator Cushion adjustment 11. Front Weight Adjustment12. Operator Cushion Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Hydraulic Oil Filter Element Engine OilChanging Engine Crankcase Oil Changing Engine Oil FilterEngine Fuel System Filling the Fuel TankReplacing In-Line Fuel Filter Elements Engine Air Cleaner Battery eLECTRIC Start ModelsCleaning and/or Replacing Air Cleaner Element Jump Starting Charging the BatteryCutter Blades Blade InspectionBlade Replacement TiresBody and deck Section Illustrated Parts List Scag Approved Attachments and Accessories61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment