Scag Power Equipment SVR61V-29FX manual Tires, Blade Replacement

Page 42

R

Section 7

Angle Blade Back

Do Not Cut In

 

X Must NOT Exceed

30

1/3 Blade Width

SGB033

 

Figure 7-7. Blade Sharpening

2.Check the balance of the blade. If the blades are out of balance, vibration and premature wear can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades.

C. Blade Replacement

WARNING

Always wear proper hand and eye protection when working with cutter blades.

1.Remove the ignition key before replacing the blades.

2.Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.

3.Secure the cutter blades to prevent them from rotating, (use the optional Blade Buddy tool, P/N 9212, to assist in securing the cutter blades), remove the nut from the blade attaching bolt. Remove the cutter blade, bolt and spacer from the spindle shaft. See Figure 7-8.

- NOTE -

The front of the machine will have to be raised slightly to remove the blade bolt from the cutter spindle.

4.To install the new cutter blade, put the flat washer onto the blade bolt and slide the bolt into the hole in the cutter blade.

- NOTE -

Be sure that the blade is installed with the lift wing pointing toward the top of the deck.

5.Install the spacer onto the blade bolt and insert the bolt into the cutter spindle shaft.

6.Install the hex nut to the blade bolt at the top of the cutter spindle. Secure the blades from rotating and torque to 75 ft/lbs. See Figure 7-8.

HEX NUT-TORQUE

TO 75 LB-FT

SPINDLE

SHAFTCUTTER DECK

HEX HEAD

BOLT / NUT

SPINDLE

ASSEMBLY

 

CUTTER BLADE

 

SPACER

 

CUTTER

WASHER

BLADE

 

 

HEX HEAD BOLT

Figure 7-8. Blade Replacement

7.9 TIRES

Check the tire pressures after every 8 hours of operation or daily.

Caster Wheels

Flat-Free

Drive Wheels

12 PSI

38

Page 41 Page 43
Image 42
Page 41 Page 43
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Following SectionDirection Reference General InformationIntroduction Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation considerations Operation Considerations Slope Angle Graph Maintenance Considerations & storage Front Tie Down PointsUsing a spark arrestor SPARK Ignition SystemSafety and Instructional Decals 483402 483407Electrical SpecificationsEngine Engine DeckWeights and Dimensions SvR-61v Cutter DeckProductivity Operating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and Steering Forward TravelReverse Travel Engaging the Deck Drive Cutter Blades Forward / Reverse ControlsParking the Mower Hillside OperationAfter Operation Removing Clogged MaterialAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking brake adjustmentTravel adjustment Neutral adjustment Tracking adjustmentCutter deck adjustments Throttle Control and Choke AdjustmentsBelt Adjustments Belt AlignmentCutter deck level Cutter deck pitchCutter Deck Height Adjustment Cutter deck heightCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected Electric clutch adjustment FrONT Weight AdjustmentOperator Cushion adjustment 11. Front Weight Adjustment12. Operator Cushion Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Hydraulic Oil Filter Element Engine OilChanging Engine Crankcase Oil Changing Engine Oil FilterEngine Fuel System Filling the Fuel TankReplacing In-Line Fuel Filter Elements Engine Air Cleaner Battery eLECTRIC Start ModelsCleaning and/or Replacing Air Cleaner Element Jump Starting Charging the BatteryCutter Blades Blade InspectionBlade Replacement TiresBody and deck Section Illustrated Parts List Scag Approved Attachments and Accessories61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment

SVR61V-29FX specifications

The Scag Power Equipment SVR61V-29FX is a standout in the realm of commercial-grade zero-turn mowers, designed to meet the demanding needs of lawn care professionals and discerning homeowners alike. This powerful machine is engineered to deliver exceptional performance, efficiency, and durability, making it a reliable choice for a variety of mowing applications.

At the heart of the SVR61V-29FX is a robust 29-horsepower Kawasaki FX series engine. This powerful engine is known for its reliability and superior performance, allowing for smooth operation and optimal cutting capabilities. The advanced air filtration system ensures that the engine operates efficiently, prolonging its life while maintaining peak performance.

One of the signature features of the SVR61V-29FX is its 61-inch Velocity Plus cutting deck. This innovative deck design is optimized for maximum airflow and cutting efficiency, allowing for a precise and clean cut even in tough mowing conditions. The heavy-duty, welded steel construction of the deck ensures durability and longevity, reducing the risk of damage over time. The deck's height is easily adjustable, providing users with the flexibility to choose their desired cutting height for various grass types.

The SVR61V-29FX is equipped with hydrostatic transmission, providing seamless control and speed management. The intuitive dual-lever steering system allows for precise maneuverability, making it easy to navigate around obstacles and tight spaces. This zero-turn capability enhances productivity by reducing the time it takes to mow large areas, a key feature for professionals seeking efficiency.

In terms of operator comfort, the SVR61V-29FX boasts a comfortable, plush seat with armrests that support extended usage without fatigue. The ergonomic design of the controls further enhances the user experience, allowing operators to efficiently manage mowing tasks without unnecessary strain.

Additionally, the SVR61V-29FX is built with a rugged frame and heavy-duty components, designed to withstand the rigors of frequent use. Scag’s commitment to quality ensures that this mower is not just a workhorse but also a long-term investment for its users.

Overall, the Scag Power Equipment SVR61V-29FX combines powerful performance, cutting-edge technology, and user-focused design characteristics, making it an exceptional choice for anyone looking to achieve professional-grade mowing results. Its combination of power, precision, and comfort sets it apart in the competitive landscape of zero-turn mowers.
Top Page Image Contents