Scag Power Equipment SVR61V-29FX manual Cutter deck level, Cutter deck pitch

Page 27

Section 6

R

Cutter deck level

The cutter deck should be level from side-to-side for proper cutting performance. To check for level, be sure that the mower is on a flat, level surface, the tires are properly inflated and the cutter deck is set at the most common cutting height that you will use. On the LH side of the machine, check the distance from the top of the cutter deck to the floor. Next check the distance from the top of the cutter deck to the floor on the RH side of the machine. Both measurements should be the same. If the two measurements are different, the cutter deck level must be adjusted as follows:

1.On the front RH side of the cutter deck locate the cutter deck adjustment levers. Loosen the elastic stop nuts securing the cutter deck adjustment levers on the front and rear of the cutter deck. See Figure 6-4.

CUTTER DECK ADJUSTMENT

BOLT

2.Turn the adjustment bolts on the front and rear cutter deck adjustment levers clockwise to raise or counter-clockwise to lower the RH side until the distance from the top of the cutter deck to the floor is the same as the measurement on the LH side of the machine.

3.Tighten the two elastic stop nuts to secure the cutter deck in the proper position.

cutter deck pitch

The pitch of the cutter deck should be equal between the front and rear of the cutter deck for proper cutting performance. To check for proper deck pitch, be sure that the mower is on a flat, level surface and the tires are properly inflated.

Check the distance from the top of the cutter deck to the floor at the rear RH side of the cutter deck. Next check the distance from the top of the cutter deck to the floor at the front RH side of the cutter deck. The measurement at the front of the cutter deck should be the same as the rear of the deck. Make these measurements at the LH side of the cutter deck also. If the measurement at the front of the deck is not the same, the cutter deck pitch must be adjusted as follows:

1.Loosen the elastic stop nuts securing the deck level links on front of the cutter deck on both sides See Figure 6-5.

2.Turn the adjustment bolts on both side either clockwise to raise or counterclockwise to lower the front of the cutter deck until the measurements are equal. Tighten the elastic stop nuts.

CUTTER DECK ADJUSTMENT

BOLT

Figure 6-4. Cutter Deck Level Adjustment

23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Following Section Limited Warranty Commercial EquipmentServicing The Engine And Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSafety Information Signal WordsBefore Operation considerations Operation Considerations Slope Angle Graph Front Tie Down Points Maintenance Considerations & storageSPARK Ignition System Using a spark arrestor483402 483407 Safety and Instructional DecalsEngine Deck SpecificationsEngine ElectricalWeights and Dimensions SvR-61v Cutter DeckProductivity Controls and Instrument Identification Operating InstructionsSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and Steering Forward TravelReverse Travel Forward / Reverse Controls Engaging the Deck Drive Cutter BladesRemoving Clogged Material Hillside OperationAfter Operation Parking the MowerAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Adjustments Parking brake adjustmentTravel adjustment Tracking adjustment Neutral adjustmentBelt Alignment Throttle Control and Choke AdjustmentsBelt Adjustments Cutter deck adjustmentsCutter deck pitch Cutter deck levelCutter deck height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected FrONT Weight Adjustment Electric clutch adjustment11. Front Weight Adjustment Operator Cushion adjustment12. Operator Cushion Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Engine Oil Filter Engine OilChanging Engine Crankcase Oil Changing Hydraulic Oil Filter ElementEngine Fuel System Filling the Fuel TankReplacing In-Line Fuel Filter Elements Engine Air Cleaner Battery eLECTRIC Start ModelsCleaning and/or Replacing Air Cleaner Element Blade Inspection Charging the BatteryCutter Blades Jump StartingTires Blade ReplacementBody and deck Section Scag Approved Attachments and Accessories Illustrated Parts List61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment

SVR61V-29FX specifications

The Scag Power Equipment SVR61V-29FX is a standout in the realm of commercial-grade zero-turn mowers, designed to meet the demanding needs of lawn care professionals and discerning homeowners alike. This powerful machine is engineered to deliver exceptional performance, efficiency, and durability, making it a reliable choice for a variety of mowing applications.

At the heart of the SVR61V-29FX is a robust 29-horsepower Kawasaki FX series engine. This powerful engine is known for its reliability and superior performance, allowing for smooth operation and optimal cutting capabilities. The advanced air filtration system ensures that the engine operates efficiently, prolonging its life while maintaining peak performance.

One of the signature features of the SVR61V-29FX is its 61-inch Velocity Plus cutting deck. This innovative deck design is optimized for maximum airflow and cutting efficiency, allowing for a precise and clean cut even in tough mowing conditions. The heavy-duty, welded steel construction of the deck ensures durability and longevity, reducing the risk of damage over time. The deck's height is easily adjustable, providing users with the flexibility to choose their desired cutting height for various grass types.

The SVR61V-29FX is equipped with hydrostatic transmission, providing seamless control and speed management. The intuitive dual-lever steering system allows for precise maneuverability, making it easy to navigate around obstacles and tight spaces. This zero-turn capability enhances productivity by reducing the time it takes to mow large areas, a key feature for professionals seeking efficiency.

In terms of operator comfort, the SVR61V-29FX boasts a comfortable, plush seat with armrests that support extended usage without fatigue. The ergonomic design of the controls further enhances the user experience, allowing operators to efficiently manage mowing tasks without unnecessary strain.

Additionally, the SVR61V-29FX is built with a rugged frame and heavy-duty components, designed to withstand the rigors of frequent use. Scag’s commitment to quality ensures that this mower is not just a workhorse but also a long-term investment for its users.

Overall, the Scag Power Equipment SVR61V-29FX combines powerful performance, cutting-edge technology, and user-focused design characteristics, making it an exceptional choice for anyone looking to achieve professional-grade mowing results. Its combination of power, precision, and comfort sets it apart in the competitive landscape of zero-turn mowers.
Top Page Image Contents