Scag Power Equipment SVR61V-29FX manual Cutter deck height, Cutter Deck Height Adjustment

Page 28

R

Section 6

CUTTER DECK ADJUSTMENT

BOLT

DECK HEIGHT

CONTROL ROD

LOOSEN HERE

CUTTER DECK ADJUSTMENT

BOLT

Figure 6-6. Cutter Deck Height Adjustment

2.Rotate the cutter blade on the left side of the cutter deck. Position the cutter blade so it is facing "front to back" on the machine.

Figure 6-5. Cutter Deck Pitch Adjustment

Cutter deck height

The cutter deck height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge. To check for proper deck height, be sure that the mower is on a flat, level surface, shut off the engine and remove the igition key. Make sure the tires are properly inflated.

1.Check the cutter deck cutting height by placing the lanyard pin in the 3" position on the cutting height index. Release the deck from the transport position and allow the deck to move to the 3" cutting height position.

24

WARNING

Always wear proper hand and eye protection when working with cutter blades.

3.Check the measurement from the floor to the cutter blade tip at the rear of the left side blade. If the measurement is not at 3", an adjustment can be made using the deck height control rod.

4.Adjust by loosening the jam nuts on the deck height control rod. Turn the deck height control rod until the 3" setting is acheived. Hold the deck height control rod and tighten the jam nuts. See Figure 6-6.

5.Once the adjustment is made to the deck height control rod, Check the measurement from the floor to the cutter blade tip at the front of the left side blade. If the measurement is not at 3", an adjustment must be made using the cutter deck adjustment lever. Adjust as follows:

A.Loosen the elastic stop nuts securing the deck level links on front of the cutter deck on both sides (See Figure 6-4 and Figure 6-5 for Cutter Deck Adjustment Lever Location).

B.Turn the adjustment bolts on both side either clockwise to raise or counterclockwise to lower the front of the cutter deck until the measurements are equal. Tighten the elastic stop nuts.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Following SectionGeneral Information IntroductionDirection Reference Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionSignal Words Safety InformationBefore Operation considerations Operation Considerations Slope Angle Graph Maintenance Considerations & storage Front Tie Down PointsUsing a spark arrestor SPARK Ignition SystemSafety and Instructional Decals 483402 483407Specifications EngineElectrical Engine DeckCutter Deck Weights and Dimensions SvR-61vProductivity Operating Instructions Controls and Instrument IdentificationInitial RUN-IN Procedures Safety Interlock SystemStarting the Engine Forward Travel Ground Travel and SteeringReverse Travel Engaging the Deck Drive Cutter Blades Forward / Reverse ControlsHillside Operation After OperationParking the Mower Removing Clogged MaterialMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Parking brake adjustment AdjustmentsTravel adjustment Neutral adjustment Tracking adjustmentThrottle Control and Choke Adjustments Belt AdjustmentsCutter deck adjustments Belt AlignmentCutter deck level Cutter deck pitchCutter Deck Height Adjustment Cutter deck heightCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected Electric clutch adjustment FrONT Weight AdjustmentOperator Cushion adjustment 11. Front Weight Adjustment12. Operator Cushion Adjustment Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Hydraulic SystemChanging Hydraulic Oil Engine Oil Changing Engine Crankcase OilChanging Hydraulic Oil Filter Element Changing Engine Oil FilterFilling the Fuel Tank Engine Fuel SystemReplacing In-Line Fuel Filter Elements Battery eLECTRIC Start Models Engine Air CleanerCleaning and/or Replacing Air Cleaner Element Charging the Battery Cutter BladesJump Starting Blade InspectionBlade Replacement TiresBody and deck Section Illustrated Parts List Scag Approved Attachments and Accessories61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment

SVR61V-29FX specifications

The Scag Power Equipment SVR61V-29FX is a standout in the realm of commercial-grade zero-turn mowers, designed to meet the demanding needs of lawn care professionals and discerning homeowners alike. This powerful machine is engineered to deliver exceptional performance, efficiency, and durability, making it a reliable choice for a variety of mowing applications.

At the heart of the SVR61V-29FX is a robust 29-horsepower Kawasaki FX series engine. This powerful engine is known for its reliability and superior performance, allowing for smooth operation and optimal cutting capabilities. The advanced air filtration system ensures that the engine operates efficiently, prolonging its life while maintaining peak performance.

One of the signature features of the SVR61V-29FX is its 61-inch Velocity Plus cutting deck. This innovative deck design is optimized for maximum airflow and cutting efficiency, allowing for a precise and clean cut even in tough mowing conditions. The heavy-duty, welded steel construction of the deck ensures durability and longevity, reducing the risk of damage over time. The deck's height is easily adjustable, providing users with the flexibility to choose their desired cutting height for various grass types.

The SVR61V-29FX is equipped with hydrostatic transmission, providing seamless control and speed management. The intuitive dual-lever steering system allows for precise maneuverability, making it easy to navigate around obstacles and tight spaces. This zero-turn capability enhances productivity by reducing the time it takes to mow large areas, a key feature for professionals seeking efficiency.

In terms of operator comfort, the SVR61V-29FX boasts a comfortable, plush seat with armrests that support extended usage without fatigue. The ergonomic design of the controls further enhances the user experience, allowing operators to efficiently manage mowing tasks without unnecessary strain.

Additionally, the SVR61V-29FX is built with a rugged frame and heavy-duty components, designed to withstand the rigors of frequent use. Scag’s commitment to quality ensures that this mower is not just a workhorse but also a long-term investment for its users.

Overall, the Scag Power Equipment SVR61V-29FX combines powerful performance, cutting-edge technology, and user-focused design characteristics, making it an exceptional choice for anyone looking to achieve professional-grade mowing results. Its combination of power, precision, and comfort sets it apart in the competitive landscape of zero-turn mowers.
Top Page Image Contents