Scag Power Equipment SVR61V-29FX manual Engine Oil, Changing Engine Crankcase Oil

Page 38

R

Section 7

HYDRAULIC OIL

DRAIN PLUG	FILTER

B. Changing Engine Crankcase Oil

After the first 20 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or monthly, whichever occurs first. Refer to the Engine Operator’s Manual furnished with this mower for instructions.

ENGINE OIL

FILLER & DIPSTICK

ENGINE OIL

FILTER

Figure 7-3. Hydraulic Oil Filter

C. Changing Hydraulic Oil Filter Element

The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first.

1.Remove the oil filter element. See Figure 7-3. Properly discard the oil filter element. Fill the new filter with clean oil and install the filter. Hand tighten only.

2.Run the engine at idle speed with the speed control lever in neutral for five minutes.

3.Check the oil level in the hydraulic tank. Hydraulic oil must be at the full tab below the filler neck. If necessary, add SAE 20w50 motor oil.

7.4 Engine Oil

ENGINE OIL

DRAIN

Figure 7-4. Drain Plug, Dipstick and Oil Filter

Location

C. Changing Engine Oil Filter

After the first 20 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for instructions.

A. Checking Engine Crankcase Oil Level

The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator’s Manual furnished with this mower.

34

DANGER

To avoid injury from burns, allow the mower to cool before changing the oil and removing the filter.

Image 38

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Limited Warranty Commercial Equipment Following SectionDirection Reference General InformationIntroduction Servicing The Engine And Drive Train ComponentsSymbols Symbol DescriptionBefore Operation considerations Safety InformationSignal Words Operation Considerations Slope Angle Graph Maintenance Considerations & storage Front Tie Down PointsUsing a spark arrestor SPARK Ignition SystemSafety and Instructional Decals 483402 483407Electrical SpecificationsEngine Engine DeckProductivity Weights and Dimensions SvR-61vCutter Deck Operating Instructions Controls and Instrument IdentificationStarting the Engine Safety Interlock SystemInitial RUN-IN Procedures Reverse Travel Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Forward / Reverse ControlsParking the Mower Hillside OperationAfter Operation Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Troubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Travel adjustment AdjustmentsParking brake adjustment Neutral adjustment Tracking adjustmentCutter deck adjustments Throttle Control and Choke AdjustmentsBelt Adjustments Belt AlignmentCutter deck level Cutter deck pitchCutter Deck Height Adjustment Cutter deck heightCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected Electric clutch adjustment FrONT Weight AdjustmentOperator Cushion adjustment 11. Front Weight Adjustment12. Operator Cushion Adjustment Maintenance Maintenance Chart Recommended Service Intervals Maintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic Oil Filter Element Engine OilChanging Engine Crankcase Oil Changing Engine Oil FilterReplacing In-Line Fuel Filter Elements Engine Fuel SystemFilling the Fuel Tank Cleaning and/or Replacing Air Cleaner Element Engine Air CleanerBattery eLECTRIC Start Models Jump Starting Charging the BatteryCutter Blades Blade InspectionBlade Replacement TiresBody and deck Section Illustrated Parts List Scag Approved Attachments and Accessories61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment