Scag Power Equipment SVR61V-29FX manual Custom-Cut Baffle Adjustment

Page 29

Section 6

R

6.Rotate the cutter blade on the right side of the cutter deck. Position the cutter blade so it is facing "front to back" on the machine.

7.Check the measurement from the floor to the cutter blade tip at the front and rear of the right side blade. If the measurement is not at 3", an adjustment must be made using the cutter deck adjustment lever.

Adjust as follows:

A. Loosen the elastic stop nuts securing the deck level links on front of the cutter deck on both sides (See Figure 6-4 and Figure 6-5 for Cutter Deck Adjustment Lever Location).

B.Turn the adjustment bolts on both side either clockwise to raise or counterclockwise to lower the cutter deck until the measurements are equal. Tighten the elastic stop nuts.

Custom-Cut Baffle Adjustment

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in seven (7) different positions for optimum performance.

A.3-1/2" or 3-3/4" Position - See Figure 6-7. For very tall, wiry or tough-to-cut grass.

B.4" (factory setting), 4-1/4" or 4-1/2" Position - See Figure 6-7. For general purpose cutting. This gives the best mix of cutting performance in all types of grass.

C.4-3/4" or 5-1/4" Position - See Figure 6-7. Placing the baffle in either the 4-3/4" or 5-1/4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To adjust the Custom-Cut Baffle height:

1.Park the machine on a flat surface, apply the parking brake, shut off the engine and remove the key.

2.Place the cutter deck in the transport position.

3.Remove the hardware securing the Custom-Cut Baffle to the cutter deck.

- NOTE -

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

4.Move the Custom-Cut Baffle to desired position. See Figures 6-7.

5.Reinstall the mounting hardware. Torque hardware to 39 ft-lbs.

25

Page 28 Page 30
Image 29
Page 28 Page 30
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Following Section Limited Warranty Commercial EquipmentIntroduction General InformationDirection Reference Servicing The Engine And Drive Train ComponentsSymbol Description SymbolsBefore Operation considerations Safety InformationSignal Words Operation Considerations Slope Angle Graph Front Tie Down Points Maintenance Considerations & storageSPARK Ignition System Using a spark arrestor483402 483407 Safety and Instructional DecalsEngine SpecificationsElectrical Engine DeckProductivity Weights and Dimensions SvR-61vCutter Deck Controls and Instrument Identification Operating InstructionsStarting the Engine Safety Interlock SystemInitial RUN-IN Procedures Reverse Travel Ground Travel and SteeringForward Travel Forward / Reverse Controls Engaging the Deck Drive Cutter BladesAfter Operation Hillside OperationParking the Mower Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Condition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Cutting Conditions Contd Scalping Blades Hitting Travel adjustment AdjustmentsParking brake adjustment Tracking adjustment Neutral adjustmentBelt Adjustments Throttle Control and Choke AdjustmentsCutter deck adjustments Belt AlignmentCutter deck pitch Cutter deck levelCutter deck height Cutter Deck Height AdjustmentCustom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment Mounting Slot Selected FrONT Weight Adjustment Electric clutch adjustment11. Front Weight Adjustment Operator Cushion adjustment12. Operator Cushion Adjustment Maintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Engine Crankcase Oil Engine OilChanging Hydraulic Oil Filter Element Changing Engine Oil FilterReplacing In-Line Fuel Filter Elements Engine Fuel SystemFilling the Fuel Tank Cleaning and/or Replacing Air Cleaner Element Engine Air CleanerBattery eLECTRIC Start Models Cutter Blades Charging the BatteryJump Starting Blade InspectionTires Blade ReplacementBody and deck Section Scag Approved Attachments and Accessories Illustrated Parts List61V Cutter Deck Description SVR-61V Cutter Deck Controls Three Weights Installed SVR-61V Sheet Metal Components Brake Shaft Support SVR-61V Steering Controls Brake Lever w/Grip SVR-61V SVR-61V Fuel System EPA Phase SVR-61V Fuel System EPA Phase Models produced after to 1/1/2011 Hose, Vapor Recovery 3/16 order by inch SVR-61VHYDRAULICS and Engine Components SVR-61V Hydraulics and Engine Components Electrical System Instrument Panel w/Decal Switch, PTO 10 Amp 48798 Heavy-Duty Commercial Replacement Decals and Information Plates SVR Electrical Schematic Limited Warranty Commercial Equipment

SVR61V-29FX specifications

The Scag Power Equipment SVR61V-29FX is a standout in the realm of commercial-grade zero-turn mowers, designed to meet the demanding needs of lawn care professionals and discerning homeowners alike. This powerful machine is engineered to deliver exceptional performance, efficiency, and durability, making it a reliable choice for a variety of mowing applications.

At the heart of the SVR61V-29FX is a robust 29-horsepower Kawasaki FX series engine. This powerful engine is known for its reliability and superior performance, allowing for smooth operation and optimal cutting capabilities. The advanced air filtration system ensures that the engine operates efficiently, prolonging its life while maintaining peak performance.

One of the signature features of the SVR61V-29FX is its 61-inch Velocity Plus cutting deck. This innovative deck design is optimized for maximum airflow and cutting efficiency, allowing for a precise and clean cut even in tough mowing conditions. The heavy-duty, welded steel construction of the deck ensures durability and longevity, reducing the risk of damage over time. The deck's height is easily adjustable, providing users with the flexibility to choose their desired cutting height for various grass types.

The SVR61V-29FX is equipped with hydrostatic transmission, providing seamless control and speed management. The intuitive dual-lever steering system allows for precise maneuverability, making it easy to navigate around obstacles and tight spaces. This zero-turn capability enhances productivity by reducing the time it takes to mow large areas, a key feature for professionals seeking efficiency.

In terms of operator comfort, the SVR61V-29FX boasts a comfortable, plush seat with armrests that support extended usage without fatigue. The ergonomic design of the controls further enhances the user experience, allowing operators to efficiently manage mowing tasks without unnecessary strain.

Additionally, the SVR61V-29FX is built with a rugged frame and heavy-duty components, designed to withstand the rigors of frequent use. Scag’s commitment to quality ensures that this mower is not just a workhorse but also a long-term investment for its users.

Overall, the Scag Power Equipment SVR61V-29FX combines powerful performance, cutting-edge technology, and user-focused design characteristics, making it an exceptional choice for anyone looking to achieve professional-grade mowing results. Its combination of power, precision, and comfort sets it apart in the competitive landscape of zero-turn mowers.
Top Page Image Contents