Remington Power Tools ES1514US, ES1512US Entire Length Of Log On Ground, Log Supported On One End

Page 13

OPERATING CHAIN SAW

Entire Length Of Log On Ground

Cut log from top (see Figure 12).

Figure 12 - Bucking Log With Entire Length On Ground

Log Supported On One End

1.Make first cut on underside of log (see Figure 13). Use top of guide bar to make this cut. Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut directly above first cut. Cut down to meet first cut. This cut will keep log from pinching guide bar and chain.

2nd Cut

1st Cut

Figure 13 - Bucking Log When Log Is Supported On One End

Log Supported On Both Ends

1.Make first cut from above log (see Figure 14). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut.

2.Make second cut on underside of log, directly under first cut. Use top of guide bar to make this cut. Cut up to meet first cut. This will keep log from pinching guide bar and chain.

1st Cut

2nd Cut

Figure 14 - Bucking Log When Log Is Supported On Both Ends

TRIMMING A TREE (PRUNING)

WARNING:Avoid kickback. Kickback can result in severe injury or death. See Kickback to avoid risk of kickback.

WARNING: Do not operate chain saw while

•in a tree

•on a ladder or any other unstable sur- face

•in any awkward position

You may lose control of saw causing severe injury.

WARNING: Do not cut limbs higher than your shoulders.

CAUTION: Seek professional help if facing conditions beyond your ability.

Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow directions below to trim a tree.

1.Make first cut six inches from tree trunk on underside of limb. Use top of guide bar to make this cut. Cut 1/3 through diameter of limb (see Figure 15).

2.Move two to four inches farther out on limb. Make second cut from above limb. Continue cut until you cut limb off.

3.Make third cut as close to tree trunk as possible on underside of limb stub. Use top of guide bar to make this cut. Cut 1/3 through diameter of stub.

4.Make fourth cut directly above third cut. Cut down to meet third cut. This will remove limb stub.

2nd Cut - Pruning Cut (to avoid pinching)

4th Cut - Final Stub Cut

6" (15 cm)

2" to 4"

(5 a 10 cm)

1st Cut - Pruning Undercut (to avoid splintering)

3rd Cut - Stub Undercut (to avoid splintering)

Figure 15 - Cutting A Limb

ENGLISH

13

www.remingtonpowertools.com

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Models Electric Chain SAWCall 1-800-626-2237 for Technical Assistance Stop Para ArrétEnglish ContentsBefore Operating SAW Important Safety InformationWhile Operating SAW Read ALL InstructionsKickback Kickback Safety Devices On This SawMaintenance and Storage Chain SAW Saw Maintenance and Kickback SafetyUnpacking Remove all items from cartonChain SAW Names and Terms Product IdentificationImportant Do not clamp chain saw in vise during assembly AssemblyTurning Adjusting Screw SAW Chain Tension AdjustmentOiling Chain Operating Chain SAW Filling OIL TankCutting with the Chain SAW Extension CordsOperating Chain SAW Felling Procedure Felling NotchFelling a Tree Cutting Down a Tree Before Felling a TreeBucking a LOG Limbing a TreeFollow directions on page 13 to buck a log Log Supported On One End Entire Length Of Log On GroundLog Supported On Both Ends Trimming a Tree PruningCleaning SAW Body Cleaning and MaintenanceNormal Guide Bar Maintenance Care of Guide BARSharpening Cutters Items Needed to Sharpen ChainFiling Cutter Depth Gauges Replacement Parts and Accessories Technical ServiceRepair Service StorageObserved Fault Possible Cause Remedy TroubleshootingRemington Brand Electric Chain SAW Limited Warranties Warranty InformationBox Bowling Green, KY M8W 1T2Modelos Sierra EléctricaLimpieza Y Mantenimiento Información Importante DE SeguridadAL Utilizar LA Sierra Antes DE Utilizar LA SierraLEA Todas LAS Instrucciones Lleve la sierra eléctrica de un lugar a otro ContragolpesCon el dedo fuera del gatillo Mantenimiento de la cadena y seguridad contra contragolpes DesembalajeMantenimiento Y Almacenamiento DE SU Sierra Eléctrica Cuide de su sierra eléctrica Nunca la exponga a la lluviaTerminología Identificación DEL ProductoRueda dentada Rueda dentada que impulsa la cadena Figura 2- Ensamble de la Barra Guía, Cadena EnsamblajeFigura 4 Girando el Tornillo de Regulación Ajuste DE Tensión DE LA Cadena SerradaLubricación USO DE LA Sierra EléctricaCables DE Prolongación Lubricación DE LA CadenaAntes de derribar un árbol Tala DE UN Árbol Derribamiento de un árbolAdvertencia Despeje el área de trabajo alrededor del árbolTala final Procedimiento de tala Corte de la muescaDesmembramiento DE UN Árbol Corte en dirección a la muescaTronco apoyado en un extremo La totalidad del tronco sobre el sueloTrozado DE UN Tronco Siga estas instrucciones para trozar un troncoPoda DE UN Árbol Tronco apoyado sobre ambos extremosLa presión del tronco Limpieza DEL Cabezal Limpieza Y MantenimientoCuidado DE LA Barra DE Guía Afilado DE LA CadenaLimado de los calibradores de medida de profundidad Afilado de los elementos de corteServicio Técnico AlmacenamientoAccesorios Y Piezas DE Repuesto Servicio DE ReparaciónFalla Observada Causa Posible Solución Diagnóstico Y Resolución DE ProblemasAkron Road Información DE GarantíaBox Toronto, Ontario M8W 1T2 Bowling Green, KY 100089-06A, ES1512US, ES1514US, ES1514AS ModèlesNettoyage ET Entretien Consignes DE Sécurité ImportantesAvant D’UTILISER LA Tronçonneuse Consignes DE Sécurité ImportantesPendant Lutilisation DE LA Tronçonneuse Lisez Toutes LES InstructionsRecul Entretien ET Remisage DE LA Tronçonneuse Entretien de la tronçonneuse et protection contre le reculFaire très attention quand on repénètre dans une entaille Déballage Identification DU ProduitAbattage Coupe d’un arbre Vocabulaire DE LA TronçonneuseAssemblage du guide-chaîne, de la chaîne et du protège-main MontageComment tourner la vis de réglage Réglage DE LA Tension DE LA ChaîneRallonges Électriques Utilisation DE LA TronçonneuseLubrification DE LA Chaîne Sciage Avec LA TronçonneuseAvant d’abattre un arbre Abattage D’UN ArbreAvertissement Trait d’abattage Procédure d’abattage Sifflet d’abattageÉbranchage Tronçonnage D’UNE Bille Toute la bille repose au solLa bille est soutenue à une extrémité La bille est soutenue aux deuxCoupe dune branche Taille D’UN Arbre ÉlagageNettoyage DU Carter DE Tronçonneuse Nettoyage ET EntretienEntretien DE LA GUIDE-CHAÎNE Entretien normal de la guide-chaîneAffûtage des taillants Outils nécessaires pour affûter la chaîneLimage des limiteurs de profondeur des taillants Remarque Limer au milieu de la guide-chaînePièces DE Rechange ET Accessoires Service TechniqueService DE Réparation Remplacement DE LA ChaîneDéfaillance Cause Possible Remède Observée DépannageBox Bowling Green, KY Information SUR LA GarantiePage Gear, Drive II 20DP Parts LIST/LISTA DE REPUESTOS/LISTE DES PiècesParts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE Pièces Page 120877-01 Rev. C 02/08

ES1514US, ES1514AS, ES1512US, 100089-06A specifications

Remington Power Tools stands as a prominent name in the arena of outdoor equipment, particularly known for their lawn and garden tools that combine efficiency, power, and ease of use. Four standout models in their lineup are the 100089-06A, ES1512US, ES1514AS, and ES1514US. Each of these tools showcases unique features catering to diverse user needs while maintaining Remington's reputation for quality.

The Remington 100089-06A is particularly appreciated for its remarkable versatility. This model comes equipped with a powerful 33cc two-cycle engine, making it an excellent choice for tackling tough yard tasks. The user-friendly design ensures easy start-up, and the ergonomic handle reduces user fatigue, allowing for prolonged operation without discomfort. Additionally, its attachment capability allows users to customize the tool based on their specific gardening needs.

Moving on to the ES1512US, this electric chainsaw is engineered for precision cutting. It features a robust 12-amp motor that provides sufficient power for various cutting tasks. The tool's lightweight design makes it accessible for both seasoned professionals and novice users. Its low kickback 12-inch bar and chain ensure safety while delivering smooth and efficient cuts. Plus, the tool is equipped with a tool-less chain tensioning system, allowing for easy adjustments on the fly.

The ES1514AS is another electric chainsaw, but with enhanced specifications. It steps up with a 14-inch bar, making it ideal for larger branches and logs. This model also carries a 15-amp motor, which enhances its cutting power substantially. One of its key technologies is the automatic oiler, which ensures that the chain remains lubricated, reducing friction and extending the life of the tool. It’s designed to operate quietly, making it a great choice for residential areas.

Lastly, the ES1514US shares many features with the ES1514AS but is distinguished by its extended user-friendly characteristics, ensuring maximum efficiency and comfort. With an ergonomic handle and a lightweight design, it provides the convenience needed for extended periods of work without fatigue. Both ES1514 models boast a safety brake feature that immediately halts the chain movement upon encountering resistance, further ensuring user safety.

In conclusion, Remington's 100089-06A, ES1512US, ES1514AS, and ES1514US showcase a blend of power, safety, and user-friendly innovations. Each tool is tailored to meet different gardening and lawn care needs, making them invaluable assets for both casual gardeners and dedicated landscapers alike.
Top Page Image Contents