Remington Power Tools Filling OIL Tank, Operating Chain SAW, Extension Cords, Oiling Chain

Page 17

SAW CHAIN TENSION ADJUSTMENT

Continued

2.Turn adjusting screw clockwise until all slack is out of chain (see Figure 5). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 6).

3.Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise.

4.After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension.

FILLING OIL TANK

1.Remove oil cap.

2.Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil.

3.Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank.

4.Wipe off excess oil.

Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage.

OPERATING CHAIN SAW

WARNING: Read and understand this owner’smanualbeforeoperatingthissaw. Make certain you read and understand all Important Safety Information, pages 2 through 4.Improper use of this chain saw can cause severe injury or death from fire,electrical shock,or body contact with moving chain, or falling wood.

EXTENSION CORDS

Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW.

Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below.

Cord Length

AWG Cord Size

 

 

25 feet

16 AWG

50 feet

16 AWG

100 feet

16 AWG

150 feet

14 AWG

Models Pole Saw Assy: 104317, 106821, and

106821A; Pole Saw: 104316-04, 104316-05 (8˝/20.3 cm),106890-01,106890-02 (10˝/25.4 cm), and 108526-01 [8˝(20.3 cm), 10˝ (25.4 cm)]

Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords.

The extension cord may come undone from the power cord during use. To avoid this, make a knot with the two cords as shown in Figure 7.

OILING CHAIN

Always check oil level before using saw. Do not attempt to operate the oil system while saw is in operation. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least once before each cut. Check oil level often by looking at oil sight level hole. Oil sight level hole is on left side of saw, between front handle and front hand guard.

CUTTING WITH THE CHAIN SAW

1.Connect saw to extension cord. Connect exten- sion cord to power supply.

2.Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain.

3.Use both hands to grip saw. Always use left hand to grip front handle and right hand to grip rear handle. Use firm grip. Thumbs and fingers must wrap around saw handles (see Figure 9).

4.Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.

5.When ready to make a cut, press in switch lockout with right thumb and squeeze trigger (see Figure 9). This will turn saw on. Releasing trigger will turn saw off. Make sure saw is running at full speed before starting a cut.

Continued

108539

17

www.desatech.com

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MODELS/MODELOS/MODÈLES Manual Para EL Usuario Manuel D’UTILISATION ET D’ENTRETIENBefore Operating SAW Important Safety InformationWhile Operating SAW Read ALL InstructionsSaw Maintenance and Kickback Safety Kickback Safety Devices On This SawMaintenance and Storage of Chain SAW KickbackAntes DE Utilizar LA Sierra Información Importante DE SeguridadA dry place LEA Todas LAS InstruccionesContragolpes AL Utilizar LA SierraLleve la sierra eléctrica de un lugar a otro Con el dedo fuera del gatilloCuide de su sierra eléctrica Nunca la exponga a la lluvia Mantenimiento de la cadena y seguridad contra contragolpesMantenimiento Y Almacenamiento DE SU Sierra Eléctrica Avant D’UTILISER LA Tronçonneuse Consignes DE Sécurité ImportantesPendant Lutilisation DE LA Tronçonneuse Lisez Toutes LES InstructionsSuite Entretien ET Remisage DE LA Tronçonneuse ReculEntretien de la tronçonneuse et protection contre le recul ’utilisation sécuritaire et correcte de la tronçonneuse FIGURES/FIGURAS/FIGURESFIGURES/FIGURAS/ Figures FIGURES/FIGURAS Limbing a Tree Guide Bar Cross Section Showing Uneven Bar Wear Unpacking Electric Chain SAWChain SAW Names and Terms Remove all items from cartonImportant Do not clamp chain saw in vise during assembly AssemblySAW Chain Tension Adjustment Operating Chain SAW Filling OIL TankExtension Cords Oiling ChainFelling a Tree Cutting Down a Tree Felling Procedure Felling NotchBefore Felling a Tree Felling CutTrimming a Tree Pruning Limbing a TreeBucking a LOG Cleaning SAW Body Cleaning MaintenanceCare of Guide BAR Sharpening SAW ChainReplacement Parts and Accessories Technical ServiceStorage Filing Cutter Depth GaugesWarranty Service Repair ServiceNON-WARRANTY Service Pole SAW AssemblyObserved Fault Possible Cause Remedy TroubleshootingIndustries of Canada, Inc Electric Chain SAW Limited WarrantyModel Date Purchased Desembalaje Sierra EléctricaTerminología EnsamblajeAjuste DE Tensión DE LA Cadena Serrada USO DE LA Sierra Eléctrica LubricaciónCables DE Prolongación Lubricación DE LA CadenaAntes de derribar un árbol Tala DE UN Árbol Derribamiento de un árbolProcedimiento de tala Corte de la muesca Tala finalTrozado DE UN Tronco Desmembramiento DE UN ÁrbolLa totalidad del tronco sobre el suelo Siga estas instrucciones para trozar un troncoTronco apoyado en un extremo Limpieza Y MantenimientoTronco apoyado sobre ambos extremos Poda DE UN ÁrbolAfilado DE LA Cadena Cuidado DE LA Barra DE GuíaServicio Técnico AlmacenamientoAccesorios Y Piezas DE Repuesto Recambio DE LA Cadena SerradaServicio SIN Garantía Servicio DE ReparaciónServicio CON Garantía Falla Observada Causa Posible Solución Diagnóstico Y Resolución DE ProblemasModelo Fecha de compra Garantía Limitada DE Sierra EléctricaDéballage Tronçonneuse Électrique PrimeVocabulaire DE LA Tronçonneuse MontageÉtendez la chaîne, bien à plat Réglage DE LA Tension DE LA ChaîneRemplissage DU Réservoir D’HUILE Rallonges Électriques Utilisation DE LA TronçonneuseLubrification DE LA Chaîne Sciage Avec LA TronçonneuseAvant d’abattre un arbre Abattage D’UN ArbreProcédure d’abattage Sifflet d’abattage Trait d’abattageTronçonnage D’UNE Bille ÉbranchageToute la bille repose au sol La bille est soutenue à une extrémitéTaille D’UN Arbre Élagage Nettoyage ET EntretienNettoyage DU Carter DE Tronçonneuse Entretien DE LA GUIDE-CHAÎNEAffûtage DE LA Chaîne Remplacement DE LA ChaîneRemisage Pièces DE Rechange ET Accessoires Service TechniqueNuméro De pièce Description 104301S Chaîne, 20,3 cm 8 po 075752 Pignon d’entraînementService Hors Garantie Service DE RéparationService Sous Garantie Défaillance Observée Cause Possible Remède DépannageModèle Date dachat Information SUR LA GarantieGarantie Limitée Pour LA Tronçonneuse Électrique Parts CENTRAL/CENTRAL DE PIEZAS/DÉPÔT DE Pièces LNT-2 113614-01 Parts LIST/LISTA DE REPUESTOS/LISTE DES Pièces108539 108539 108539-01 Rev. K 10/05

104316-04, 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A, 106890-01 specifications

Remington Power Tools has established a reputation for providing high-quality outdoor power equipment, and their latest lineup includes a range of innovative models such as the 106890-01, 104316-04, 104316-05, 106890-02, 108526-01, 104317, 106821, and 106821A. These products are designed to enhance user experience while delivering reliable performance in various landscaping and yard maintenance tasks.

One of the standout models, the Remington 106890-01, features a powerful engine that ensures consistent performance across different terrains. This model is equipped with advanced air filtration technology, which helps in prolonging engine life and optimizing performance by reducing dust and debris entering the system. Its ergonomic design also enhances user comfort, making it easy to handle during extended use.

The 104316-04 and 104316-05 models share several characteristics, including easy-start mechanisms that allow users to begin work without hassle. Their lightweight design ensures mobility, making them ideal for homeowners and professionals alike. Both models also come with adjustable cutting widths, allowing users to customize their landscaping tasks according to specific needs.

Moving on to the 106890-02, it incorporates modern vibration-dampening technology, which significantly reduces user fatigue while working. This model is perfect for those long hours spent managing larger properties. The incorporated safety features, including automatic shut-off and safety guards, ensure that users can operate the tool with confidence.

The 108526-01 model is particularly notable for its versatility. Designed with multiple attachments, it can easily transform from a trimmer to an edger or blower, making it an all-in-one solution for various lawn and garden tasks. Its powerful motor delivers reliability across different attachments, ensuring a seamless transition during use.

The 104317 model stands out with its innovative battery technology that promises longer run times and faster charging. This feature is especially beneficial for users who prefer cordless options. Both the 106821 and 106821A models focus on energy efficiency and are fitted with eco-friendly engines that meet modern emissions standards, appealing to environmentally-conscious consumers.

In summary, Remington Power Tools continues to innovate with models like 106890-01, 104316-04, 104316-05, 106890-02, 108526-01, 104317, 106821, and 106821A. With their commitment to performance, safety, and user comfort, these power tools are set to meet the diverse needs of homeowners and landscaping professionals alike. Each model is a testament to the brand's dedication to providing durable, efficient, and user-friendly equipment that enhances outdoor living.
Top Page Image Contents