RedMax EXZ-PU, EX-HE, EX2-BC, EX-PS, EX-LRT manual Using the Product,  10 

Page 10

5. For safe operation

WARNING

Make sure the throttle is at idle position.

Never place the throttle into the high speed position or half throttle position (throttle lock position) when starting the engine.

3.After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position (idle position). If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized Red Max servicing dealer for repair.

USING THE PRODUCT

IMPORTANT

Cut only materials recommended by the manufacturer. And use only for tasks explained in the manual.

1.Grip the handles firmly with both hands using your whole hand. Place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.

2.Keep cutting attachment below waist level.

3.Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary.

4.If the unit start to shake or vibrate, turn off the engine and check the whole unit. Do not use it until the trouble has been properly corrected.

5.Keep all parts of your body away from rotating cutting attachment and hot surfaces.

6.Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. Doing so could result in serious burns or electrical shock.

10

Image 10
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 EX-PS SpecificationsEX-LRT EX-HE 5  Symbols on the machine  6 Working Circumstance For safe operationWorking Condition  7 Working Plan  8 Starting the Engine Before Starting the Engine 9  Using the Product  10 Handling Fuel MaintenanceIf Someone Comes  11 Transportation  12 Set up  13 Installing Cutting Head SE2 Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Balance UnitMain pipe Trimming mechanism Screw hole Fastening bolt Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1  15 EX-PS SE2 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE3Hole Moving direction Chain tensioner nut Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6  17 Clamp bolt Lock screw Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 BracketFuel and chain oil When using Zenoah genuine oilHOW to MIX Fuel Recommended Mixing Ratio Gasoline 50OIL 20  Fueling the UnitFor Your Engine LIFE, Avoid Chain OIL EX-PS onlyOperation  21 Stopping Engine OP6 OP6 OP7 OP8 22  OP9 Adjusting Throttle CableAdjusting Idling Speed OP10  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 Cutting Method EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle  26 What causes blade thrust EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust  27 How you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  EX-LRT OP1 Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only Clamp lever Trimming mechanismEX-PS OP1 EX-PS OP2 Checking OIL Supply Adjusting OIL Flow RateOperation EX-PS only  31  32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35  Muffler MA4 36  Spark ArresterMA6 Procedures to be Performed After Every 100 Hours of USEMA51 Cylinder Intake air cooling vent backEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line Gear Case MA2Quick TIP Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Gear CaseGuide BAR Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port  40 Sprocket EX-PS MA4 MA5 MA6SAW Chain EX-PS MA7 MA8 MA9  42 MA1 Gear Case Maintenance EX-HE only 43  Check Probable Causes Action Troubleshooting guideStorage  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée