RedMax EX2-BC, EXZ-PU, EX-HE, EX-PS, EX-LRT manual OP6 OP7 OP8, Stopping Engine OP6,  22 

Page 22

8. Operation

OP6

(5)

(6)

(4)

(7)

OP7

OP8

lever is in to the “start” position. (OP6)

6.While holding the unit firmly, pull out the starter rope quickly until engine fires. (OP7)

(1)choke lever (2) close (3) open

(4)ignition switch (5) start (6) stop

(7)throttle set button

WARNING

The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by pulling the throttle. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts. (OP8)

IMPORTANT

Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.

7.Move the choke lever downward to open the choke. And restart engine. (OP5)

8.Allow the engine to warm up for a several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

STOPPING ENGINE (OP6)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the STOP position.

22

Image 22
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 EX-PS SpecificationsEX-LRT EX-HE 5  Symbols on the machine  6 Working Circumstance For safe operationWorking Condition  7 Working Plan  8 Starting the Engine Before Starting the Engine 9  Using the Product  10 Handling Fuel MaintenanceIf Someone Comes  11 Transportation  12 Set up  13 Installing Cutting Head SE2 Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Balance UnitMain pipe Trimming mechanism Screw hole Fastening bolt Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1  15 EX-PS SE2 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE3Hole Moving direction Chain tensioner nut Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6  17 Clamp bolt Lock screw Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 BracketFuel and chain oil When using Zenoah genuine oilHOW to MIX Fuel Recommended Mixing Ratio Gasoline 50OIL 20  Fueling the UnitFor Your Engine LIFE, Avoid Chain OIL EX-PS onlyOperation  21 Stopping Engine OP6 OP6 OP7 OP8 22  OP9 Adjusting Throttle CableAdjusting Idling Speed OP10  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 Cutting Method EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle  26 What causes blade thrust EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust  27 How you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  EX-LRT OP1 Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only Clamp lever Trimming mechanismEX-PS OP1 EX-PS OP2 Checking OIL Supply Adjusting OIL Flow RateOperation EX-PS only  31  32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35  Muffler MA4 36  Spark ArresterMA6 Procedures to be Performed After Every 100 Hours of USEMA51 Cylinder Intake air cooling vent backEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line Gear Case MA2Quick TIP Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Gear CaseGuide BAR Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port  40 Sprocket EX-PS MA4 MA5 MA6SAW Chain EX-PS MA7 MA8 MA9  42 MA1 Gear Case Maintenance EX-HE only 43  Check Probable Causes Action Troubleshooting guideStorage  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée