RedMax EX-LRT, EX-HE Fuel and chain oil, Recommended Mixing Ratio Gasoline 50OIL, HOW to MIX Fuel

Page 19

7. Fuel and chain oil

WARNING

Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.

The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE)

Do not use BIA or TCW (2-stroke water- cooling type) mixed oil.

RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1

(when using ZENOAH genuine oil)

50:1 MIXING CHART

GASOLINE gal. 1 2 3 4 5

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE

liter

1

2

3

4

5

 

 

 

 

 

 

 

2-CYCLE OIL

ml

20

40

60

80

100

 

 

 

 

 

 

 

Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.

These engines are certified to operate on unleaded gasoline.

Make sure to use gasoline with a minimum octane number of 89 RON (USA/Canada: 87AL)

If you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston seizing may consequently occur.

Unleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment.

Poor quality gasolines or oils may damage sealing rings, fuel lines or fuel tank of the engine.

HOW TO MIX FUEL

IMPORTANT

Pay attention to agitate carefully.

1.Measure out the quantities of gasoline and oil to be mixed.

2.Put some of the gasoline into a clean, approved fuel container.

3.Pour in all of the oil and agitate well.

4.Pour In the rest of gasoline and agitate

19

Image 19
Contents 848-J8P-93A0 OWNER/OPERATOR ManualContents Safety First 3  Parts locationEX-HE SpecificationsEX-LRT EX-PS 5   6  Symbols on the machine 7  For safe operationWorking Condition Working Circumstance 8  Working PlanStarting the Engine Before Starting the Engine 9   10  Using the Product 11  MaintenanceIf Someone Comes Handling Fuel 12  Transportation 13  Set upBalance Unit Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Installing Cutting Head SE2 15  Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1 Main pipe Trimming mechanism Screw hole Fastening boltEX-PS SE3 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2 17  Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6 Hole Moving direction Chain tensioner nutBracket Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilHOW to MIX Fuel Fuel and chain oilChain OIL EX-PS only Fueling the UnitFor Your Engine LIFE, Avoid  20  21  OperationStopping Engine OP6 OP6 OP7 OP8 22   23  Adjusting Throttle CableAdjusting Idling Speed OP10 OP9 24  Operation EX2-BC only 25  Operation Optional blade usage EX2-BC only 26  EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle Cutting Method 27  EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust What causes blade thrustHow you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  Clamp lever Trimming mechanism Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only EX-LRT OP1 31  Adjusting OIL Flow RateOperation EX-PS only EX-PS OP1 EX-PS OP2 Checking OIL Supply 32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35  Spark Arrester MA4 36  MufflerCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEMA51 MA6Gear Case MA2 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line EX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1Gear Case Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Quick TIP 40  Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port Guide BARSprocket EX-PS MA4 MA5 MA6SAW Chain  42  EX-PS MA7 MA8 MA9MA1 Gear Case Maintenance EX-HE only 43   44  Troubleshooting guideStorage Check Probable Causes ActionEX-LRT ATT EX-PS ATT EX-HE ATT Parts list 46  EXZ-PU S/N 60300000 and up 47   48  EX2-BC S/N 50200000 and up 49   50  Engine Unit 60100000 and upDescription Part Number Qty  51  52  EX-LRT S/N 000531 and upCasing B  53  54  EX-PS S/N 000000 and up 55   56  EX-HE S/N 000101 and up 57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée