RedMax EX-HE, EXZ-PU EX2-BC OP4 EX2-BC OP5 EX2-BC OP6, Bracket Handle, Cutting Method,  26 

Page 26

8. Operation (Optional blade usage EX2-BC only)

EX2-BC OP4

EX2-BC OP5

EX2-BC OP6

IMPORTANT

Change the loop handle to the J-handle for safe operation. (OP4)

(1)Bracket: 3583-14101

(2)J-handle: 6367-14200

STARTING THE ENGINE

Please refer 5.For safe operation (P.9~11), 8.Operation (P.21~22).

WARNING

The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as soon as the engine is started by putting the throttle into the start position. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts. (OP5)

CUTTING METHOD

a)Use the front left side cutting.

b)Guide the blade from your right to left with it tilted slightly to your left. (OP6)

c)When mowing a wide area, start working from your left end to avoid interference of cut grass.

d)The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object.

WARNING

If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit. Change the blade if it has been damaged.

Turn off the engine and make sure the blade has completely stop before checking the blade, and removing any object got caught in.

26

Image 26
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 EX-PS SpecificationsEX-LRT EX-HE 5  Symbols on the machine  6 Working Circumstance For safe operationWorking Condition  7 Working Plan  8  9  Before Starting the EngineStarting the Engine Using the Product  10 Handling Fuel MaintenanceIf Someone Comes  11 Transportation  12 Set up  13 Installing Cutting Head SE2 Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Balance UnitMain pipe Trimming mechanism Screw hole Fastening bolt Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1  15 EX-PS SE2 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE3Hole Moving direction Chain tensioner nut Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6  17 Clamp bolt Lock screw Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 BracketFuel and chain oil When using Zenoah genuine oilHOW to MIX Fuel Recommended Mixing Ratio Gasoline 50OIL 20  Fueling the UnitFor Your Engine LIFE, Avoid Chain OIL EX-PS onlyOperation  21  22  OP6 OP7 OP8Stopping Engine OP6 OP9 Adjusting Throttle CableAdjusting Idling Speed OP10  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 Cutting Method EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle  26 What causes blade thrust EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust  27  28  How you can reduce the chance of blade thrustHow you can maintain the best control  29  EX2-BC OP9 Maintenance BladeTransporting the Unit EX-LRT OP1 Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only Clamp lever Trimming mechanismEX-PS OP1 EX-PS OP2 Checking OIL Supply Adjusting OIL Flow RateOperation EX-PS only  31  32   33  Operation EX-HE onlyEX-HE OP1  34  MaintenanceMaintenance Chart  35  Muffler MA4 36  Spark ArresterMA6 Procedures to be Performed After Every 100 Hours of USEMA51 Cylinder Intake air cooling vent backEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line Gear Case MA2Quick TIP Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Gear CaseGuide BAR Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port  40 SAW Chain EX-PS MA4 MA5 MA6Sprocket EX-PS MA7 MA8 MA9  42  43  Maintenance EX-HE onlyMA1 Gear Case Check Probable Causes Action Troubleshooting guideStorage  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée