RedMax EX-PS, EXZ-PU, EX-HE, EX2-BC, EX-LRT manual Set up,  13 

Page 13

6. Set up

SE1

SE2

SE3

SE4

(1)

SE5

SE6

SE7 (1)

MOUNTING ENGINE (SE1)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly.

3.Fasten the clamp securely with two screws.

IMPORTANT

Tighten the screws gradually by turns.

CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2)

CONNECTING SWITCH WIRES (SE3)

Connect the switch wires between the engine and the main unit. Pair the wires of the same color.

Bind switchwires to throttle wire with tie band like figure of SE3.

(1) Tie band

INSTALLING HANDLE (EX2-BC, EX-LRT only) (SE4)

• Install the handle to the shaft tube and clamp it at a location that is comfortable to you.

(1) About 19 inches (48cm)

(EX-PS only) (SE5)

Insert the grip to the shaft tube.

Fasten the clamps with screws.

(EX-HE only) (SE6)

Install the J-shaped handle to the shaft tube and clamp at a position best for your job.

JOINT ATTACHMENT (SE7)

Insert the attachment to the main shaft.

Tighten the knob bolt securely.

(1) Knob bolt

13

Image 13
Contents 848-J8P-93A0 OWNER/OPERATOR ManualContents Safety First 3  Parts locationEX-LRT SpecificationsEX-PS EX-HE 5   6  Symbols on the machineWorking Condition For safe operationWorking Circumstance  7  8  Working PlanStarting the Engine Before Starting the Engine 9   10  Using the ProductIf Someone Comes MaintenanceHandling Fuel  11  12  Transportation 13  Set upEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Set up EX2-BC onlyInstalling Cutting Head SE2 Balance UnitEX-LRT SE1 Attaching the Trimming Mechanism SE1 Set up EX-LRT onlyMain pipe Trimming mechanism Screw hole Fastening bolt  15 EX-PS SE1 Attaching the Pruning Mechanism SE1 Set up EX-PS onlyEX-PS SE2 EX-PS SE3EX-PS SE4 EX-PS SE5 EX-PS SE6 Chain tension adjusting screw Loosen TightenHole Moving direction Chain tensioner nut  17 EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Set up EX-HE onlyClamp bolt Lock screw BracketHOW to MIX Fuel When using Zenoah genuine oilFuel and chain oil Recommended Mixing Ratio Gasoline 50OILFor Your Engine LIFE, Avoid Fueling the Unit 20  Chain OIL EX-PS only 21  OperationStopping Engine OP6 OP6 OP7 OP8 22  Adjusting Idling Speed OP10 Adjusting Throttle CableOP9  23  24  Operation EX2-BC only 25  Operation Optional blade usage EX2-BC onlyBracket Handle EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Cutting Method  26 Controlling Blade Thrust EX2-BC OP7 EX2-BC OP8 OperationWhat causes blade thrust  27 How you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  Operation EX-LRT only Adjusting the Angle of the Cutting Blades OP1EX-LRT OP1 Clamp lever Trimming mechanismOperation EX-PS only Adjusting OIL Flow RateEX-PS OP1 EX-PS OP2 Checking OIL Supply  31  32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35   36  MA4Muffler Spark ArresterMA51 Procedures to be Performed After Every 100 Hours of USEMA6 Cylinder Intake air cooling vent backFor safety reasons, do not use metalreinforced line Maintenance EX2-BC onlyEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Gear Case MA2EX-LRT MA1 EX-LRT MA2 Blades MA1 Maintenance EX-LRT onlyQuick TIP Gear CaseEX-PS MA1 MA2 MA3 Oiling Port Maintenance EX-PS onlyGuide BAR  40 Sprocket EX-PS MA4 MA5 MA6SAW Chain  42  EX-PS MA7 MA8 MA9MA1 Gear Case Maintenance EX-HE only 43  Storage Troubleshooting guideCheck Probable Causes Action  44 EX-LRT ATT EX-PS ATT EX-HE ATT Parts list 46  EXZ-PU S/N 60300000 and up 47   48  EX2-BC S/N 50200000 and up 49   50  Engine Unit 60100000 and upDescription Part Number Qty  51  52  EX-LRT S/N 000531 and upCasing B  53  54  EX-PS S/N 000000 and up 55   56  EX-HE S/N 000101 and up 57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée