RedMax EX2-BC, EXZ-PU, EX-HE, EX-PS, EX-LRT manual  32 

Page 32

8. Operation (EX-PS only)

IMPORTANT

The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw.

3.With a screwdriver, push in on the oil flow rate adjusting screw and turn in the desired direction (there are three incremental settings):

(a)Clockwise-decrease lubrication.

(b)Counter clockwise-increase lubrication.

(c)Middle

WARNING

Always wear work gloves made of leather or some other sturdy material when using the polesaw.

Falling branches may fall onto the face or into the eyes, resulting in injuries, scratches, and cuts, and for this reason you should always be sure to wear a helmet and face protector when using your polesaw.

32

Image 32
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 Specifications EX-LRTEX-PS EX-HE 5  Symbols on the machine  6 For safe operation Working ConditionWorking Circumstance  7 Working Plan  8  9  Before Starting the EngineStarting the Engine Using the Product  10 Maintenance If Someone ComesHandling Fuel  11 Transportation  12 Set up  13 Set up EX2-BC only EX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris GuardInstalling Cutting Head SE2 Balance UnitSet up EX-LRT only EX-LRT SE1 Attaching the Trimming Mechanism SE1Main pipe Trimming mechanism Screw hole Fastening bolt  15 Set up EX-PS only EX-PS SE1 Attaching the Pruning Mechanism SE1EX-PS SE2 EX-PS SE3Chain tension adjusting screw Loosen Tighten EX-PS SE4 EX-PS SE5 EX-PS SE6Hole Moving direction Chain tensioner nut  17 Set up EX-HE only EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4Clamp bolt Lock screw BracketWhen using Zenoah genuine oil HOW to MIX FuelFuel and chain oil Recommended Mixing Ratio Gasoline 50OILFueling the Unit For Your Engine LIFE, Avoid 20  Chain OIL EX-PS onlyOperation  21  22  OP6 OP7 OP8Stopping Engine OP6 Adjusting Throttle Cable Adjusting Idling Speed OP10OP9  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 EX2-BC OP4 EX2-BC OP5 EX2-BC OP6 Bracket HandleCutting Method  26 EX2-BC OP7 EX2-BC OP8 Operation Controlling Blade ThrustWhat causes blade thrust  27  28  How you can reduce the chance of blade thrustHow you can maintain the best control  29  EX2-BC OP9 Maintenance BladeTransporting the Unit Adjusting the Angle of the Cutting Blades OP1 Operation EX-LRT onlyEX-LRT OP1 Clamp lever Trimming mechanismAdjusting OIL Flow Rate Operation EX-PS onlyEX-PS OP1 EX-PS OP2 Checking OIL Supply  31  32   33  Operation EX-HE onlyEX-HE OP1  34  MaintenanceMaintenance Chart  35  MA4  36 Muffler Spark ArresterProcedures to be Performed After Every 100 Hours of USE MA51MA6 Cylinder Intake air cooling vent backMaintenance EX2-BC only For safety reasons, do not use metalreinforced lineEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Gear Case MA2Maintenance EX-LRT only EX-LRT MA1 EX-LRT MA2 Blades MA1Quick TIP Gear CaseMaintenance EX-PS only EX-PS MA1 MA2 MA3 Oiling PortGuide BAR  40 SAW Chain EX-PS MA4 MA5 MA6Sprocket EX-PS MA7 MA8 MA9  42  43  Maintenance EX-HE onlyMA1 Gear Case Troubleshooting guide StorageCheck Probable Causes Action  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée