RedMax EX-HE Set up EX-PS only, EX-PS SE1 Attaching the Pruning Mechanism SE1, EX-PS SE2,  16 

Page 16

6. Set up (EX-PS only)

EX-PS

(1)

SE1

(2)

(3)

 

(4)

 

 

(5)

ATTACHING THE PRUNING MECHANISM (SE1)

1. Remove the cap on the end of the main pipe.

2. Remove the screw screwed into the end of the gear case.

3. Insert the end of the gear case into the main pipe.

4. Line up the hole on the end of the gear case into which the screw is to be inserted with the hole on the main pipe, and screw the screw firmly in.

5. Using a wrench, screw in the bolt provided to fix the mechanism into place.

EX-PS SE2

(1)Main pipe

(2)Gear case

(3)Screw hole

(4)Fastening bolt

(5)Bolt

A standard package contains the items as shown below. (SE2)

(1)Guide bar

(2)Saw chain

(3)Gase case

(4)Sprocket

(5)Chain tension adjust screw

(6)Nut

(7)Chain tensioner nut

(8)Chain cover

Install the guide bar and the saw chain on the gear case as follows.

EX-PS SE3

WARNING

The saw chain has very sharp edges. Use protective gloves for safety.

1.Loosen a nut and remove the chain cover.

2.Mount the guide bar then fit the saw chain around the bar and sprocket. (SE3)

WARNING

Pay attention to the correct direction of the saw chain

16

Image 16
Contents OWNER/OPERATOR Manual 848-J8P-93A0Safety First ContentsParts location  3 Specifications EX-LRTEX-PS EX-HE 5  Symbols on the machine  6 For safe operation Working ConditionWorking Circumstance  7 Working Plan  8 Starting the Engine Before Starting the Engine 9  Using the Product  10 Maintenance If Someone ComesHandling Fuel  11 Transportation  12 Set up  13 Set up EX2-BC only EX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris GuardInstalling Cutting Head SE2 Balance UnitSet up EX-LRT only EX-LRT SE1 Attaching the Trimming Mechanism SE1Main pipe Trimming mechanism Screw hole Fastening bolt  15 Set up EX-PS only EX-PS SE1 Attaching the Pruning Mechanism SE1EX-PS SE2 EX-PS SE3Chain tension adjusting screw Loosen Tighten EX-PS SE4 EX-PS SE5 EX-PS SE6Hole Moving direction Chain tensioner nut  17 Set up EX-HE only EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4Clamp bolt Lock screw BracketWhen using Zenoah genuine oil HOW to MIX FuelFuel and chain oil Recommended Mixing Ratio Gasoline 50OILFueling the Unit For Your Engine LIFE, Avoid 20  Chain OIL EX-PS onlyOperation  21 Stopping Engine OP6 OP6 OP7 OP8 22  Adjusting Throttle Cable Adjusting Idling Speed OP10OP9  23 Operation EX2-BC only  24 Operation Optional blade usage EX2-BC only  25 EX2-BC OP4 EX2-BC OP5 EX2-BC OP6 Bracket HandleCutting Method  26 EX2-BC OP7 EX2-BC OP8 Operation Controlling Blade ThrustWhat causes blade thrust  27 How you can maintain the best control How you can reduce the chance of blade thrust 28  Transporting the Unit EX2-BC OP9 Maintenance Blade 29  Adjusting the Angle of the Cutting Blades OP1 Operation EX-LRT onlyEX-LRT OP1 Clamp lever Trimming mechanismAdjusting OIL Flow Rate Operation EX-PS onlyEX-PS OP1 EX-PS OP2 Checking OIL Supply  31  32  EX-HE OP1 Operation EX-HE only 33  Maintenance Chart Maintenance 34   35  MA4  36 Muffler Spark ArresterProcedures to be Performed After Every 100 Hours of USE MA51MA6 Cylinder Intake air cooling vent backMaintenance EX2-BC only For safety reasons, do not use metalreinforced lineEX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1 Gear Case MA2Maintenance EX-LRT only EX-LRT MA1 EX-LRT MA2 Blades MA1Quick TIP Gear CaseMaintenance EX-PS only EX-PS MA1 MA2 MA3 Oiling PortGuide BAR  40 Sprocket EX-PS MA4 MA5 MA6SAW Chain EX-PS MA7 MA8 MA9  42 MA1 Gear Case Maintenance EX-HE only 43  Troubleshooting guide StorageCheck Probable Causes Action  44 Parts list EX-LRT ATT EX-PS ATT EX-HE ATTEXZ-PU S/N 60300000 and up  46  47  EX2-BC S/N 50200000 and up  48  49  Engine Unit 60100000 and up  50  51  Description Part Number QtyEX-LRT S/N 000531 and up  52  53  Casing BEX-PS S/N 000000 and up  54  55  EX-HE S/N 000101 and up  56  57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée