RedMax EX-PS, EXZ-PU, EX-HE OP9, Adjusting Throttle Cable, Adjusting Idling Speed OP10,  23 

Page 23

8. Operation

OP9

.04 in

(1~2mm) (1)

OP10

(1)

IMPORTANT

Except for an emergency, avoid stopping the engine while pulling the throttle lever.

ADJUSTING THROTTLE CABLE

The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP9)

(1) cable adjuster

ADJUSTING IDLING SPEED (OP10)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise.

(1) idle adjusting screw

NOTE

Warm up the engine before adjusting the idling speed.

23

Image 23
Contents 848-J8P-93A0 OWNER/OPERATOR ManualContents Safety First 3  Parts locationEX-HE SpecificationsEX-LRT EX-PS 5   6  Symbols on the machine 7  For safe operationWorking Condition Working Circumstance 8  Working Plan 9  Before Starting the EngineStarting the Engine  10  Using the Product 11  MaintenanceIf Someone Comes Handling Fuel 12  Transportation 13  Set upBalance Unit Set up EX2-BC onlyEX2-BC SE1 EX2-BC SE2 EX2-BC SE3 Installing Debris Guard Installing Cutting Head SE2 15  Set up EX-LRT onlyEX-LRT SE1 Attaching the Trimming Mechanism SE1 Main pipe Trimming mechanism Screw hole Fastening boltEX-PS SE3 Set up EX-PS onlyEX-PS SE1 Attaching the Pruning Mechanism SE1 EX-PS SE2 17  Chain tension adjusting screw Loosen TightenEX-PS SE4 EX-PS SE5 EX-PS SE6 Hole Moving direction Chain tensioner nutBracket Set up EX-HE onlyEX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 Clamp bolt Lock screwRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilHOW to MIX Fuel Fuel and chain oilChain OIL EX-PS only Fueling the UnitFor Your Engine LIFE, Avoid  20  21  Operation 22  OP6 OP7 OP8Stopping Engine OP6  23  Adjusting Throttle CableAdjusting Idling Speed OP10 OP9 24  Operation EX2-BC only 25  Operation Optional blade usage EX2-BC only 26  EX2-BC OP4 EX2-BC OP5 EX2-BC OP6Bracket Handle Cutting Method 27  EX2-BC OP7 EX2-BC OP8 OperationControlling Blade Thrust What causes blade thrust 28  How you can reduce the chance of blade thrustHow you can maintain the best control  29  EX2-BC OP9 Maintenance BladeTransporting the Unit Clamp lever Trimming mechanism Adjusting the Angle of the Cutting Blades OP1Operation EX-LRT only EX-LRT OP1 31  Adjusting OIL Flow RateOperation EX-PS only EX-PS OP1 EX-PS OP2 Checking OIL Supply 32   33  Operation EX-HE onlyEX-HE OP1  34  MaintenanceMaintenance Chart  35  Spark Arrester MA4 36  MufflerCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEMA51 MA6Gear Case MA2 Maintenance EX2-BC onlyFor safety reasons, do not use metalreinforced line EX2-BC MA1 EX2-BC MA2 Refilling Trimming Line MA1Gear Case Maintenance EX-LRT onlyEX-LRT MA1 EX-LRT MA2 Blades MA1 Quick TIP 40  Maintenance EX-PS onlyEX-PS MA1 MA2 MA3 Oiling Port Guide BARSAW Chain EX-PS MA4 MA5 MA6Sprocket  42  EX-PS MA7 MA8 MA9 43  Maintenance EX-HE onlyMA1 Gear Case  44  Troubleshooting guideStorage Check Probable Causes ActionEX-LRT ATT EX-PS ATT EX-HE ATT Parts list 46  EXZ-PU S/N 60300000 and up 47   48  EX2-BC S/N 50200000 and up 49   50  Engine Unit 60100000 and upDescription Part Number Qty  51  52  EX-LRT S/N 000531 and upCasing B  53  54  EX-PS S/N 000000 and up 55   56  EX-HE S/N 000101 and up 57  Manufacturer’s warranty coverage Limited Warranty RedMax Garantie limitée