RedMax HE250F manual OP5, OP6, OP7, Stopping Engine OP4, Adjusting Throttle Cable

Page 28

OP5

English

8. Operation

IMPORTANT

•Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.

6.Move the choke lever downward to open the choke. And restart engine. (OP3)

7.Allow the engine to warm up for several minutes before starting operation.

NOTE

OP6

.04 in

(1~2mm) (1)

OP7

(1)

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

■STOPPING ENGINE (OP4)

1.Release the throttle lever and run the engine for a half minute.

2.Shift the ignition switch to the STOP position. (OP4)

IMPORTANT

•Except for an emergency, avoid stopping the engine while pulling the throttle lever.

■ADJUSTING THROTTLE CABLE

•The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP6)

(1) cable adjuster

■ADJUSTING IDLING SPEED (OP7)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise.

(1) idle adjusting screw

NOTE

•Warm up the engine before adjusting the idling speed.

28

Image 28

Contents HE250F Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsHE250F Fiche technique Emplacement des pieces Situación de las piezasEspecificaciohes Position Symbols on the machineEmission Control Posición EmplacementControl DE Emisiones Working Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineArranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManipulación DEL Combustible Llenar una vez que el motor se haya enfriadoSet up SE1 Mounting Other PartsScrew Clamp bolt Tightning Torque 52~69in-lbs 6~8N.m SE2Assemblage Montaje Montage D’AUTRES Pieces Montaje DE Otras PartesFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Adjusting Wheel Height OperationOP1 OP2 OP3 OP4Fonctionnement Uso Couple de serrage 51~68in-lbs 6~8N.mPar de torsión de apriete 51~68in-lbs 6~8N.m Mise EN Marche DU MoteurAdjusting Throttle Cable Adjusting Idling Speed OP7OP5 OP6Arret DU Moteur OP4 Reglage Câble D’ACCÉLÉRATEURReglage DU Ralenti OP7 Cómo Parar EL Motor OP4HOW to USE OP8Fonctionnement Uso Comment Utiliser LE COUPE-BORDURES Como UsarMaintenance Be Sure to Check the Following Before Using Your Stick EdgerEntretien MantenimientoMaintenance Chart Tableau D’ENTRETIEN MantenimientoTabla DE Mantenimiento Replacement Plug is a NGK BPMR7A MA1 MA2 MA3MA4 AIR FilterEntretien Mantenimiento Muffler MA5 MA6 MA7 Spark ArresterSpark arrester Gear CaseCaja DE Cambios PARE-ETINCELLESCarter D’ENGRENAGE ParachispasIntake AIR Cooling Vent MA9 MA8 Blade MA8Cylinder Intake air cooling vent back Ouïe DU Refroidissement PAR AIR Toma DE Aire DE RefrigeraciónProcedures to be Performed After Every 100 Hours of USE StorageDisposal ProtectorEntretien Mantenimiento Rangement AlmacenamientoMise au rebut Eliminación Protecteur Protector12. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes HE250F NotaDrive Unit HE250F S/N 70200101 and up Pipe Comp Engine Unit HE250F S/N 70200101 and up Front Housing Limited Warranty Garantie limitée Garantía Limitada