Radware VOYA-GRAND-PMH, VOYA-GRAND-MBK owner manual White Wire

Page 45

R

VOYAGEUR GRAND Wood Insert

	White Wire
	Black Wire
	Green
Fiber	Grounding
Wrapped	Wire
Wire

Figure 45.1

8.The power cord is now disconnected from the blower control plate. Pull the cord out through the right side of the appliance.

Grommet

Route Cord Through

Retainer Clip

Figure 45.2

9.Insert the power cord throught the left side of the appliance in the hole contains the grommet. Pull the connection ends to the right side. Route the power cord through the retainer clip.

Strain Relief

Figure 45.3

10.Replace the strain relief on the power cord in the same position as before. Locate the indentation on the cord made by the strain relief. Once replaced, push the strain relief back into the control plate.

Figure 45.4

11.Connect the white wire on the power cord into the fiber wrapped wire on the wire harness. Connect the black wire on the power cord to the white wire on the rheostat. Re-attach the green ground terminal to the control plate.

Figure 45.5

12.Insert the control plate assembly back into the appliance as shown. Tilt the assembly forward and then lift up and rotate the bottom towards the front of the appliance at the same time ensure that the snap disc holder is properly seated. Secure plate to the appliance.

Route Wires through Retainer Clip

Replace Screws in Hold Down Bracket

Figure 45.6

13.Push in the blower and hold down bracket into appliance matching up the tab on the bracket and placement slot on the appliance. Secure bracket and reconnect blower wires (no polarity to worry about) routing wires through the retainer clip.

September 25, 2012

7075-166

Page 45

Image 45

Contents Hot glass will cause burns Voyageur Grand Wood InsertWelcome to the Quadra-Fire Family Voyageur Grand Wood InsertTable of Contents Limited Lifetime Warranty Warranty Conditions Glass Specifications BTU & Efficiency SpecificationsListing and Code Approvals Appliance CertificationOperating Instructions Your Wood ApplianceGeneral Operating Parts Combustible/Non-combustible Materials Voyageur Grand Wood Insert Fire SafetyOverfiring Seasoned WoodKindling or First Stage Voyageur Grand Wood Insert Burning ProcessSecond Stage Final StageVoyageur Grand Wood Insert Automatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Incorrect Positions Fuel Reloading Instructions Voyageur Grand Wood Insert Building a FireMoisture Wood FuelBlower Operating Instructions Frequently Asked Questions Voyageur Grand Wood Insert Clear SpaceOpacity Smoke Your specific model Voyageur Grand Wood Insert Quick Start GuideChimney and Chimney Connector Inspection/Cleaning Maintenance and ServiceCleaning Plated Surfaces Disposal of AshesInspect Firebrick & Replacement Instructions Voyageur Grand Wood Insert Glass CleaningVoyageur Grand Wood Insert Quick Reference Maintenance Guide Start Fire Problems Possible Cause Solution Troubleshooting GuideGlass Replacement Service Parts ReplacementSnap Disc Replacement Contd Snap Disc ReplacementShock Risk Voyageur Grand Wood Insert Blower ReplacementVoyageur Grand Wood Insert Door Handle Assembly Baffle & Ceramic Blanket Removal51mm. Figure Voyageur Grand Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft Voyageur Grand Wood Insert Negative Pressure Chimney Termination Requirements Voyageur Grand Wood Insert Locating Your Stove & ChimneyVoyageur Grand Wood Insert Rule Voyageur Grand Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Burn Check List Appliance Dimensions Dimensions and ClearancesWall Clear of Ashes Thermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kVenting Systems Chimney SystemsInspections Larger ChimneysVoyageur Grand Wood Insert Masonry Chimney Cont’d Prefabricated Metal Chimney Voyageur Grand Wood Insert Metal Heat Circulating MasonryVoyageur Grand Wood Insert Securing Chimney Components Altering the FireplaceFactory-Built Sold Fuel Fireplace Chimney Height / Rise and Run Items Needed for Installation not supplied Outside Air Kit InstallationOption One Outside Air Installation Instructions Option Two Outside Air Installation InstructionsLeveling Legs Flue Adapter VerticalDegree Standard Surround & Trim Kit Installation 42.1 Voyageur Grand Wood Insert Standard Surround & Cast Trim KitVoyageur Grand Wood Insert All Cast Surround Kit Blower Cord Installation on Left SidePlacement Slot Blower Access Assembly White Wire Mobile Home Installation Service Parts Part number list on followingCast Iron Wood Insert Large Stocked #10 Brick AssemblyAt Depot #7 Baffle Protection ChannelDescription Comments Part Number #13 Door Assembly#14 Access Assembly #17 Control Asembly Assemblies #25 & 26 SurroundDate of Service Performed By Description of Service Voyageur Grand Wood Insert Service And Maintenance LogVoyageur Grand Wood Insert Service And Maintenance Log Voyageur Grand Wood Insert Homeowner’s Notes Contact Information