Makita BBX7600CA Before Starting the Engine, Checking and Refilling Engine Oil

Page 10

BEFORE STARTING THE ENGINE

1. Checking and Refilling Engine Oil

1)Follow the procedure below when the engine oil is cold i.e. the blower has not been running.

•Inspection: Set the blower down on a level surface and remove the oil cap. Make sure that the oil level is within the upper and lower limit marks on the oil level gauge. If the oil is not up to the 100mL level, fill up with new oil.

•Adding Oil:Set the blower down on a level surface and remove the oil cap. Fill the oil up to the upper limit of the oil level gauge.

2)On average, engine oil normally needs to be added after every 20 hours of operation. This interval for every change in oil corresponds to refuelling the blower approximately 10-15 times.

3)Please change the oil whenever it becomes dirty or significantly changes color. (Refer to p.15 for the oil change procedure and frequency.)

Oil level gauge

Upper limit

Remain 100 mL

Lower limit

Recommended oil: Makita genuine oil or SAE10W-30 oil of API type SF grade or better (4 stroke motor oil for automobiles)

Oil capacity: Approximately 0.22 L (220 ml)

CAUTION

•If the blower is not stored in an upright position, the oil may flow from the level gauge into the engine and give a false reading when checking the oil level. This may result in inadvertently overfilling whenever adding engine oil. Always store in an upright position.

•If the upper oil level limit is exceeded, the oil may become dirty and white smoke may appear due to burning excessive oil.

Check Point #1: The oil cap

•Wipe off dirt and grime around the opening before removing the oil cap.

•Remove the oil cap and place it on a clean surface so that it does not accumulate any sand, dirt, or other foreign materials. These may stick to the cap and adulterate the engine oil. Dirty oil containing sand, dirt, or foreign materials may cause excessive wear on the engine due to improper lubrication and cause a breakdown.

Check Point #2: Oil spillage

•Oil spillage on the outside on the blower may cause the engine oil becoming dirty or adulterated. Therefore, please wipe off any oil spillage before starting the engine.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents English / Français / Español Instructions D’EMPLOI Instrucciones DE ManejoImportante Symbols Table of ContentsPersonal Protective Equipment Safety InstructionsGeneral Instructions Pay particular attention to the following regulationsRefuelling Method of operation Maintenance instructionsWhen asking for help, please give the following information First AidTechnical Data BBX7600CADesignation of Parts Designation of PartsAssembly of Blower Pipes Assembly InstructionsAlways wear protective gloves Attachment Procedure Attaching the Shoulder StrapCheck Point #1 The oil cap Before Starting the EngineChecking and Refilling Engine Oil Check Point #2 Oil spillageStorage of machine and refill tank Fuel supplyPoints for Fuel Operation When the engine is cold or after refuellingStarting When the cruise control lever is a Low-speed position Adjustment of IdlingWhen the engine is warm StoppingOperation Method Adjusting Shoulder strapAdjusting the control lever Transporting and Storing the BlowerOil Change Procedure Inspection and MaintenanceReplacement of engine oil Points in replacement of engine oilCleaning of air cleaner Checking the spark plugReplacement of gaskets and packings Cleaning the fuel filterCleaning of parts StorageFault location Perform initial replacement after 20h operationTroubleshooting State of abnormality Probable cause malfunction RemedyMakita Limited ONE Year Warranty Warranty PolicyEmission Compliance Period Emission Component Defect Warranty Period Federal Emission Component Defect WarrantyParts Covered What is not Covered Obtaining Warranty ServiceOWNER’S Warranty Responsibilities HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Interval Symboles Table des MatièresEquipements de protection Consignes DE SecuriteGénéralités Prêtez une attention particulière aux consignes suivantesPlein de carburant MètresPremiers secours MaintenanceFonctionnement ConditionnementCaractéristiques Techniques Liste DES Pièces Désignation des piècesMontage du tube de soufflante Instructions DE MontageComplètement monté Fixation de la bandoulière Procédure de fixationPrécaution Avant DE Démarrer LE MoteurVérification et remplissage de l’huile Vérification point #1 Le bouchon à huileCarburant Alimentation en carburantDurée de stockage du carburant RavitaillementMise en marche FonctionnementLorsque le moteur est froid, ou après le ravitaillement Verification de la rotation à petite vitesse Réglage DU RalentiArrêt Quand le moteur est échaufféRéglage du levier du régulateur Mode OperatoireRéglage de la bandoulière Manoeuvre du souffleur’essentiel lors de remplacement de l’huile à moteur Inspection ET MaintenanceRemplacement de l’huile à moteur Procédure de changement de l’huileNettoyage du filtre à air Vérification de bougie d’allumageNettoyage du filtre à carburant Remplacement des joints et garnituresRemisage Contrôle des boulons, écrous et visFaire le remplacement premier après 20h de marche Localisation des défautsEtat d’anomalie DepannageRemède Garantie Limitée D’UN AN Makita Politique de garantieSímbolos ContenidosEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones Generales Preste una atención especial a las siguientes medidasReabasteciemiento Primeros Auxilios Metodo DE FuncionamientoInstrucciones DE Mantenimiento EmbalajeDatos Técnicos Aceite del motorDenominación DE Partes Denominación DE PartesEnsamblaje de los tubos del soplador Instrucciones DE MontajeCompletamente Instalación de la correa al hombro Procedimiento de instalaciónPrecaución Antes DE Poner EN Marcha EL MotorInspección y rellenado de aceite de motor Punto de inspección N1 El tapón de aceiteCombustible Abastecimiento de combustiblePeríodo de almacenamiento del combustible Método que reaprovisiona de combustibleOperación Modo de arranqueComprobación del giro a baja velocidad Ajuste DEL RalentíModo de parar Cuando está caliente el motorAjuste la palanca de control Procedimiento DE OperaciónAjuste de la correa al hombro Operación del SopladorProcedimiento de cambio del aceite Inspección Y MantenimientoCambio del aceite del motor Puntos relacionados con el aceiteLimpieza del depurador de aire Inspección de la bujía de alta tensiónInspección de pernos, tuercas y tornillos AlmacenamientoLimpieza del filtro de combustible Limpieza de piezasLocalización de averías Investigación DE Averías Estado de la anormalidad Causa probable avería RemedioGarantía Limitada Makita DE UN AÑO Política de garantíaPage Page Advertencia
Related manuals
Manual 66 pages 13.55 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.
Top Page Image Contents