Makita BBX7600CA Operation, Starting, When the engine is cold or after refuelling

Page 12

OPERATION

1. Starting

WARNING

Never attempt engine start in a place where the fuel has been supplied.

-It may cause ignition or fire. When starting the engine, keep a distance of at least 3 m.

Exhaust gas from the engine is toxic. Do not operate the engine in a poorly-ventilated place, such as in a tunnel, building, etc.

-Operating the engine in the poorly-ventilated place may cause poisoning by exhaust gas.

In case of detection of any abnormality in sound, odor, vibration after starting, stop the engine immediately and carry out inspection.

-If the engine is operated without attending such abnormality, an accident may occur.

Make sure that the engine stops when the stop switch is set to “O” position.

1)When the engine is cold or after refuelling

(1)Set this machine on a flat space.

(2)Set the stop switch to “ I ” position.

(3)Make sure that the cruise control lever is in the low-speed position.

(4)Continue to push the primer pump until fuel comes into the

primer pump.

In general, fuel comes into the carburetor by 7 to 10 pushes.

If the primer pump is pushed excessively, an excess of

gasoline returns to the fuel tank.

(5) Lift the choke lever to the closed position.

(4) Primer pump

(5)

Close

Choke lever

 

 

 

 

 

(6)Hold the element cover with left hand to prevent the engine from moving.

(7)Pull out slowly the starter handle till a certain resistance is felt. Return the starter handle backward once from this position, then pull it out with force.

Never pull the rope to the full extension.

Once the start knob is pulled, never release your hand immediately. Hold the start knob until it returns to its original point.

(8)When the engine starts, open the choke lever.

Open the choke lever fully when checking the engine oper- ation.

In cold or when the engine is cooled down, never open the choke lever suddenly. Otherwise, the engine may stop.

(9)Continue warm-up operation for 2 to 3 minutes.

(10)Warm-up is complete when there is quick engine acceleration from low rpm to full throttle.

(2)

Stop Switch

(3)

Hi-speed

 

 

Cruise control lever

Low-speed

(7)

(8)

Open

12

Image 12
Contents Instructions D’EMPLOI Instrucciones DE Manejo English / Français / EspañolImportante Symbols Table of ContentsSafety Instructions General InstructionsPersonal Protective Equipment Pay particular attention to the following regulationsRefuelling Maintenance instructions When asking for help, please give the following informationMethod of operation First AidTechnical Data BBX7600CADesignation of Parts Designation of PartsAssembly Instructions Assembly of Blower PipesAlways wear protective gloves Attachment Procedure Attaching the Shoulder StrapBefore Starting the Engine Checking and Refilling Engine OilCheck Point #1 The oil cap Check Point #2 Oil spillageFuel supply Storage of machine and refill tankPoints for Fuel When the engine is cold or after refuelling OperationStarting Adjustment of Idling When the engine is warmWhen the cruise control lever is a Low-speed position StoppingAdjusting Shoulder strap Adjusting the control leverOperation Method Transporting and Storing the BlowerInspection and Maintenance Replacement of engine oilOil Change Procedure Points in replacement of engine oilCleaning of air cleaner Checking the spark plugCleaning the fuel filter Cleaning of partsReplacement of gaskets and packings StorageFault location Perform initial replacement after 20h operationTroubleshooting State of abnormality Probable cause malfunction RemedyMakita Limited ONE Year Warranty Warranty PolicyEmission Compliance Period Federal Emission Component Defect Warranty Emission Component Defect Warranty PeriodParts Covered Obtaining Warranty Service What is not CoveredOWNER’S Warranty Responsibilities HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Interval Symboles Table des MatièresConsignes DE Securite GénéralitésEquipements de protection Prêtez une attention particulière aux consignes suivantesPlein de carburant MètresMaintenance FonctionnementPremiers secours ConditionnementCaractéristiques Techniques Liste DES Pièces Désignation des piècesInstructions DE Montage Montage du tube de soufflanteComplètement monté Fixation de la bandoulière Procédure de fixationAvant DE Démarrer LE Moteur Vérification et remplissage de l’huilePrécaution Vérification point #1 Le bouchon à huileAlimentation en carburant Durée de stockage du carburantCarburant RavitaillementFonctionnement Mise en marcheLorsque le moteur est froid, ou après le ravitaillement Réglage DU Ralenti ArrêtVerification de la rotation à petite vitesse Quand le moteur est échaufféMode Operatoire Réglage de la bandoulièreRéglage du levier du régulateur Manoeuvre du souffleurInspection ET Maintenance Remplacement de l’huile à moteur’essentiel lors de remplacement de l’huile à moteur Procédure de changement de l’huileNettoyage du filtre à air Vérification de bougie d’allumageRemplacement des joints et garnitures RemisageNettoyage du filtre à carburant Contrôle des boulons, écrous et visFaire le remplacement premier après 20h de marche Localisation des défautsDepannage Etat d’anomalieRemède Garantie Limitée D’UN AN Makita Politique de garantieSímbolos ContenidosInstrucciones DE Seguridad Instrucciones GeneralesEquipo Personal de Protección Preste una atención especial a las siguientes medidasReabasteciemiento Metodo DE Funcionamiento Instrucciones DE MantenimientoPrimeros Auxilios EmbalajeDatos Técnicos Aceite del motorDenominación DE Partes Denominación DE PartesInstrucciones DE Montaje Ensamblaje de los tubos del sopladorCompletamente Instalación de la correa al hombro Procedimiento de instalaciónAntes DE Poner EN Marcha EL Motor Inspección y rellenado de aceite de motorPrecaución Punto de inspección N1 El tapón de aceiteAbastecimiento de combustible Período de almacenamiento del combustibleCombustible Método que reaprovisiona de combustibleOperación Modo de arranqueAjuste DEL Ralentí Modo de pararComprobación del giro a baja velocidad Cuando está caliente el motorProcedimiento DE Operación Ajuste de la correa al hombroAjuste la palanca de control Operación del SopladorInspección Y Mantenimiento Cambio del aceite del motorProcedimiento de cambio del aceite Puntos relacionados con el aceiteLimpieza del depurador de aire Inspección de la bujía de alta tensiónAlmacenamiento Limpieza del filtro de combustibleInspección de pernos, tuercas y tornillos Limpieza de piezasLocalización de averías Investigación DE Averías Estado de la anormalidad Causa probable avería RemedioGarantía Limitada Makita DE UN AÑO Política de garantíaPage Page Advertencia
Related manuals
Manual 66 pages 13.55 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.