Makita BBX7600CA instruction manual Cleaning of air cleaner, Checking the spark plug

Page 16

2. Cleaning of air cleaner

WARNING: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

(1)Loosen the knob bolts.

(2)Remove the air cleaner cover.

(3)Take out the element and remove any dirt from the element with the brush.

Note: The element is a dry type and should not get wet. Never wash with water.

(4)Replace the element with a new one if it is damaged or very dirty.

(5)Wipe off any oil that has come in to contact with the breather with a rag or cloth.

(6)Install the element in the cleaner case.

(7)Attach the air cleaner cover and tighten the knob bolt.

Knob bolt

Element cover

Element

Breather

DANGER

Clean the element several times a day, if excessive dust adheres to it.

If operation continues with the element remaining not cleared of oil, oil in the air cleaner may fall outside, resulting in oil contamination.

3.Checking the spark plug

CAUTION

When removing the spark plug, clean the spark plug and cylinder head first, so that no dirt, sand, etc will enter the cylinder.

You must remove the spark plug after the engine has cooled down in order to avoid damaging the threaded hole in the cylinder.

The spark plug must be installed properly into the threaded hole. If installed at an angle, the threaded hole in the cylinder will get damaged.

(1) Opening/closing the plug cover

To open the plug cover, pull up on the seam of the plug cover projection and slide in the direction of the “OPEN” indication as shown in the figure at right.

When closing the cover, slide the cover in the “CLOSE” direction till the click under the plug cover projection rides over the engine cover. Finally, push in the projection.

(2) Removing the spark plug

Use an attached box wrench to remove or install the spark plug.

(3) Checking the spark plug

The clearance between two electrodes of spark plug (see the figure left) is

0.7to 0.8 mm. Adjust to the correct clearance when it is too wide or too narrow.

Clean thoroughly or replace the spark plug if it has accumulated carbon or contaminated.

(4)Replacing the spark plug

For replacement, use NGK-CMR6A.

Lateral electrode (–)

Electrode clearance 0.7 - 0.8 mm

16

Image 16
Contents English / Français / Español Instructions D’EMPLOI Instrucciones DE ManejoImportante Symbols Table of ContentsSafety Instructions General InstructionsPersonal Protective Equipment Pay particular attention to the following regulationsRefuelling Maintenance instructions When asking for help, please give the following informationMethod of operation First AidTechnical Data BBX7600CADesignation of Parts Designation of PartsAssembly of Blower Pipes Assembly InstructionsAlways wear protective gloves Attachment Procedure Attaching the Shoulder StrapBefore Starting the Engine Checking and Refilling Engine OilCheck Point #1 The oil cap Check Point #2 Oil spillageStorage of machine and refill tank Fuel supplyPoints for Fuel Operation When the engine is cold or after refuellingStarting Adjustment of Idling When the engine is warmWhen the cruise control lever is a Low-speed position StoppingAdjusting Shoulder strap Adjusting the control leverOperation Method Transporting and Storing the BlowerInspection and Maintenance Replacement of engine oilOil Change Procedure Points in replacement of engine oilCleaning of air cleaner Checking the spark plugCleaning the fuel filter Cleaning of partsReplacement of gaskets and packings StorageFault location Perform initial replacement after 20h operationTroubleshooting State of abnormality Probable cause malfunction RemedyMakita Limited ONE Year Warranty Warranty PolicyEmission Compliance Period Emission Component Defect Warranty Period Federal Emission Component Defect WarrantyParts Covered What is not Covered Obtaining Warranty ServiceOWNER’S Warranty Responsibilities HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Interval Symboles Table des MatièresConsignes DE Securite GénéralitésEquipements de protection Prêtez une attention particulière aux consignes suivantesPlein de carburant MètresMaintenance FonctionnementPremiers secours ConditionnementCaractéristiques Techniques Liste DES Pièces Désignation des piècesMontage du tube de soufflante Instructions DE MontageComplètement monté Fixation de la bandoulière Procédure de fixationAvant DE Démarrer LE Moteur Vérification et remplissage de l’huilePrécaution Vérification point #1 Le bouchon à huileAlimentation en carburant Durée de stockage du carburantCarburant RavitaillementMise en marche FonctionnementLorsque le moteur est froid, ou après le ravitaillement Réglage DU Ralenti ArrêtVerification de la rotation à petite vitesse Quand le moteur est échaufféMode Operatoire Réglage de la bandoulièreRéglage du levier du régulateur Manoeuvre du souffleurInspection ET Maintenance Remplacement de l’huile à moteur’essentiel lors de remplacement de l’huile à moteur Procédure de changement de l’huileNettoyage du filtre à air Vérification de bougie d’allumageRemplacement des joints et garnitures RemisageNettoyage du filtre à carburant Contrôle des boulons, écrous et visFaire le remplacement premier après 20h de marche Localisation des défautsEtat d’anomalie DepannageRemède Garantie Limitée D’UN AN Makita Politique de garantieSímbolos ContenidosInstrucciones DE Seguridad Instrucciones GeneralesEquipo Personal de Protección Preste una atención especial a las siguientes medidasReabasteciemiento Metodo DE Funcionamiento Instrucciones DE MantenimientoPrimeros Auxilios EmbalajeDatos Técnicos Aceite del motorDenominación DE Partes Denominación DE PartesEnsamblaje de los tubos del soplador Instrucciones DE MontajeCompletamente Instalación de la correa al hombro Procedimiento de instalaciónAntes DE Poner EN Marcha EL Motor Inspección y rellenado de aceite de motorPrecaución Punto de inspección N1 El tapón de aceiteAbastecimiento de combustible Período de almacenamiento del combustibleCombustible Método que reaprovisiona de combustibleOperación Modo de arranqueAjuste DEL Ralentí Modo de pararComprobación del giro a baja velocidad Cuando está caliente el motorProcedimiento DE Operación Ajuste de la correa al hombroAjuste la palanca de control Operación del SopladorInspección Y Mantenimiento Cambio del aceite del motorProcedimiento de cambio del aceite Puntos relacionados con el aceiteLimpieza del depurador de aire Inspección de la bujía de alta tensiónAlmacenamiento Limpieza del filtro de combustibleInspección de pernos, tuercas y tornillos Limpieza de piezasLocalización de averías Investigación DE Averías Estado de la anormalidad Causa probable avería RemedioGarantía Limitada Makita DE UN AÑO Política de garantíaPage Page Advertencia
Related manuals
Manual 66 pages 13.55 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.