Makita BBX7600CA instruction manual Adjustment of Idling, Stopping, Checkup of low-speed rotation

Page 13

NOTE

•The engine may be damaged if the choke lever is moved further beyond the “CLOSE” position.

•If the engine fires and stops, return this lever to the “OPEN” position and pull the starter handle several times to start the engine again.

•If the operator keeps pulling the starter handle several times with the choke lever left in the “CLOSE” position, the engine may be difficult to start because of flooding of the fuel.

•In case of flooding of the fuel, remove the spark plug and pull the handle several times rapidly to discharge any excess fuel. Dry the spark plug electrode.

•When the throttle valve does not return to a position in contact with the idling adjusting screw even if the throttle lever is set to the low speed, correct the control cable catching state to ensure proper return of the valve.

2)When the engine is warm

(1)Put the engine on a flat ground.

(2)Press the primary pump several times.

(3)Make sure that the choke lever is open.

(4)Hold the element cover with left hand to prevent the engine from moving.

(5)Pull out slowly the starter handle till a certain resistance is felt. Return the starter handle backward once from this position, then pull it out with force.

(6)When the engine is difficult to start, open the throttle valve by about 1/3.

2.Stopping

1)When the cruise control lever is a Low-speed position.

Release the trigger lever to reduce the engine speed, and set the stop switch to the “O” position.

2)When the cruise control lever is except a Low-speed position.

Set the cruise control lever to the Low-speed position, reduce the engine speed, and set the stop switch to the “O” position.

Cruise control lever

Hi-speed

Low-speed

Stop Switch

ADJUSTMENT OF IDLING

DANGER

The carburetor is factory adjusted. Please do not adjust other than idling adjusting. When adjustment becomes necessary, please consult your dealership or an authorized service agent.

Checkup of low-speed rotation

Set the low-speed rotation to 2800 rpm (/min).

•If it is necessary to change the rotation speed, regulate the adjusting screw, with Phillips screwdriver.

•Turn the adjusting screw to the right, and the engine speed will increase. Turn the adjusting screw to the left, and the engine speed will drop.

Carburetor

Adjusting screw

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents English / Français / Español Instructions D’EMPLOI Instrucciones DE ManejoImportante Table of Contents SymbolsGeneral Instructions Safety InstructionsPersonal Protective Equipment Pay particular attention to the following regulationsRefuelling When asking for help, please give the following information Maintenance instructionsMethod of operation First AidBBX7600CA Technical DataDesignation of Parts Designation of PartsAssembly of Blower Pipes Assembly InstructionsAlways wear protective gloves Attaching the Shoulder Strap Attachment ProcedureChecking and Refilling Engine Oil Before Starting the EngineCheck Point #1 The oil cap Check Point #2 Oil spillageStorage of machine and refill tank Fuel supplyPoints for Fuel Operation When the engine is cold or after refuellingStarting When the engine is warm Adjustment of IdlingWhen the cruise control lever is a Low-speed position StoppingAdjusting the control lever Adjusting Shoulder strapOperation Method Transporting and Storing the BlowerReplacement of engine oil Inspection and MaintenanceOil Change Procedure Points in replacement of engine oilChecking the spark plug Cleaning of air cleanerCleaning of parts Cleaning the fuel filterReplacement of gaskets and packings StoragePerform initial replacement after 20h operation Fault locationState of abnormality Probable cause malfunction Remedy TroubleshootingWarranty Policy Makita Limited ONE Year WarrantyEmission Compliance Period Emission Component Defect Warranty Period Federal Emission Component Defect WarrantyParts Covered What is not Covered Obtaining Warranty ServiceOWNER’S Warranty Responsibilities HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Interval Table des Matières SymbolesGénéralités Consignes DE SecuriteEquipements de protection Prêtez une attention particulière aux consignes suivantesMètres Plein de carburantFonctionnement MaintenancePremiers secours ConditionnementCaractéristiques Techniques Désignation des pièces Liste DES PiècesMontage du tube de soufflante Instructions DE MontageComplètement monté Procédure de fixation Fixation de la bandoulièreVérification et remplissage de l’huile Avant DE Démarrer LE MoteurPrécaution Vérification point #1 Le bouchon à huileDurée de stockage du carburant Alimentation en carburantCarburant RavitaillementMise en marche FonctionnementLorsque le moteur est froid, ou après le ravitaillement Arrêt Réglage DU RalentiVerification de la rotation à petite vitesse Quand le moteur est échaufféRéglage de la bandoulière Mode OperatoireRéglage du levier du régulateur Manoeuvre du souffleurRemplacement de l’huile à moteur Inspection ET Maintenance’essentiel lors de remplacement de l’huile à moteur Procédure de changement de l’huileVérification de bougie d’allumage Nettoyage du filtre à airRemisage Remplacement des joints et garnituresNettoyage du filtre à carburant Contrôle des boulons, écrous et visLocalisation des défauts Faire le remplacement premier après 20h de marcheEtat d’anomalie DepannageRemède Politique de garantie Garantie Limitée D’UN AN MakitaContenidos SímbolosInstrucciones Generales Instrucciones DE SeguridadEquipo Personal de Protección Preste una atención especial a las siguientes medidasReabasteciemiento Instrucciones DE Mantenimiento Metodo DE FuncionamientoPrimeros Auxilios EmbalajeAceite del motor Datos TécnicosDenominación DE Partes Denominación DE PartesEnsamblaje de los tubos del soplador Instrucciones DE MontajeCompletamente Procedimiento de instalación Instalación de la correa al hombroInspección y rellenado de aceite de motor Antes DE Poner EN Marcha EL MotorPrecaución Punto de inspección N1 El tapón de aceitePeríodo de almacenamiento del combustible Abastecimiento de combustibleCombustible Método que reaprovisiona de combustibleModo de arranque OperaciónModo de parar Ajuste DEL RalentíComprobación del giro a baja velocidad Cuando está caliente el motorAjuste de la correa al hombro Procedimiento DE OperaciónAjuste la palanca de control Operación del SopladorCambio del aceite del motor Inspección Y MantenimientoProcedimiento de cambio del aceite Puntos relacionados con el aceiteInspección de la bujía de alta tensión Limpieza del depurador de aireLimpieza del filtro de combustible AlmacenamientoInspección de pernos, tuercas y tornillos Limpieza de piezasLocalización de averías Estado de la anormalidad Causa probable avería Remedio Investigación DE AveríasPolítica de garantía Garantía Limitada Makita DE UN AÑOPage Page Advertencia
Related manuals
Manual 66 pages 13.55 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.
Top Page Image Contents