Makita BBX7600 Operation Method, Transporting and Storing the Blower, Adjusting Shoulder strap

Page 14

OPERATION METHOD

1. Adjusting Shoulder strap

Adjust the shoulder strap to a length that is comfortable to work while carrying the blower.

Adjust as shown in the figure.

2. Adjusting the control lever

Move the control handle along the swivel pipe to the most comfortable position.

3. Blower Operation

While operating the blower, adjust the throttle bar so that the wind force is appropriate for the work location and conditions.

Low speed: Dried leaves and grass

High speed: Gravel and dirt

The cruise control lever allows the operator to maintain a constant engine speed without operating the trigger lever.

Lifting the cruise control lever increases engine speed. Lowering the cruise control lever decreases engine speed.

Adjusting engine speed when the cruise control lever is being used:

When increasing engine speed:

•Pull the trigger lever to increase engine speed. Engine speed returns to its original setting when the trigger lever is released.

•Increasing the engine speed in this manner also increases the cruise control setting. The cruise control lever lifts simultaneously as the trigger lever is pulled, and the new cruise control setting will be main- tained at the higher engine speed.

When reducing engine speed:

• Lower the cruise control lever to the low-speed position.

To tighten straps

To loosen straps

 

 

 

 

 

 

 

 

 

 

 

 

 

Cruise control lever

Hi-speed

Low-speed

TRANSPORTING AND STORING THE BLOWER

Please maintain the blower in an upright position whenever transporting or storing. (Refer to Figure at right.)

Transporting or storing in a position that is not upright may cause oil to spill inside the blower engine. This may result in oil leaks and white smoke from burning oil, and the air cleaner may become dirty with oil.

DANGER

• When transporting the blower, be sure to stop the engine.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Importante Instructions D’EMPLOI Instrucciones DE ManejoEnglish / Français / Español Symbols Table of ContentsPersonal Protective Equipment Safety InstructionsGeneral Instructions Pay particular attention to the following regulationsRefuelling Method of operation Maintenance instructionsWhen asking for help, please give the following information First AidTechnical Data BBX7600CADesignation of Parts Designation of PartsAlways wear protective gloves Assembly InstructionsAssembly of Blower Pipes Attachment Procedure Attaching the Shoulder StrapCheck Point #1 The oil cap Before Starting the EngineChecking and Refilling Engine Oil Check Point #2 Oil spillagePoints for Fuel Fuel supplyStorage of machine and refill tank Starting When the engine is cold or after refuellingOperation When the cruise control lever is a Low-speed position Adjustment of IdlingWhen the engine is warm StoppingOperation Method Adjusting Shoulder strapAdjusting the control lever Transporting and Storing the BlowerOil Change Procedure Inspection and MaintenanceReplacement of engine oil Points in replacement of engine oilCleaning of air cleaner Checking the spark plugReplacement of gaskets and packings Cleaning the fuel filterCleaning of parts StorageFault location Perform initial replacement after 20h operationTroubleshooting State of abnormality Probable cause malfunction RemedyMakita Limited ONE Year Warranty Warranty PolicyEmission Compliance Period Parts Covered Federal Emission Component Defect WarrantyEmission Component Defect Warranty Period OWNER’S Warranty Responsibilities Obtaining Warranty ServiceWhat is not Covered HOW to Make a Claim MANUFACTURER’S Warranty Coverage Page Procedure Interval Symboles Table des MatièresEquipements de protection Consignes DE SecuriteGénéralités Prêtez une attention particulière aux consignes suivantesPlein de carburant MètresPremiers secours MaintenanceFonctionnement ConditionnementCaractéristiques Techniques Liste DES Pièces Désignation des piècesComplètement monté Instructions DE MontageMontage du tube de soufflante Fixation de la bandoulière Procédure de fixationPrécaution Avant DE Démarrer LE MoteurVérification et remplissage de l’huile Vérification point #1 Le bouchon à huileCarburant Alimentation en carburantDurée de stockage du carburant RavitaillementLorsque le moteur est froid, ou après le ravitaillement FonctionnementMise en marche Verification de la rotation à petite vitesse Réglage DU RalentiArrêt Quand le moteur est échaufféRéglage du levier du régulateur Mode OperatoireRéglage de la bandoulière Manoeuvre du souffleur’essentiel lors de remplacement de l’huile à moteur Inspection ET MaintenanceRemplacement de l’huile à moteur Procédure de changement de l’huileNettoyage du filtre à air Vérification de bougie d’allumageNettoyage du filtre à carburant Remplacement des joints et garnituresRemisage Contrôle des boulons, écrous et visFaire le remplacement premier après 20h de marche Localisation des défautsRemède DepannageEtat d’anomalie Garantie Limitée D’UN AN Makita Politique de garantieSímbolos ContenidosEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones Generales Preste una atención especial a las siguientes medidasReabasteciemiento Primeros Auxilios Metodo DE FuncionamientoInstrucciones DE Mantenimiento EmbalajeDatos Técnicos Aceite del motorDenominación DE Partes Denominación DE PartesCompletamente Instrucciones DE MontajeEnsamblaje de los tubos del soplador Instalación de la correa al hombro Procedimiento de instalaciónPrecaución Antes DE Poner EN Marcha EL MotorInspección y rellenado de aceite de motor Punto de inspección N1 El tapón de aceiteCombustible Abastecimiento de combustiblePeríodo de almacenamiento del combustible Método que reaprovisiona de combustibleOperación Modo de arranqueComprobación del giro a baja velocidad Ajuste DEL RalentíModo de parar Cuando está caliente el motorAjuste la palanca de control Procedimiento DE OperaciónAjuste de la correa al hombro Operación del SopladorProcedimiento de cambio del aceite Inspección Y MantenimientoCambio del aceite del motor Puntos relacionados con el aceiteLimpieza del depurador de aire Inspección de la bujía de alta tensiónInspección de pernos, tuercas y tornillos AlmacenamientoLimpieza del filtro de combustible Limpieza de piezasLocalización de averías Investigación DE Averías Estado de la anormalidad Causa probable avería RemedioGarantía Limitada Makita DE UN AÑO Política de garantíaPage Page Advertencia
Related manuals
Manual 66 pages 13.55 Kb

BBX7600CA, BBX7600 specifications

The Makita BBX7600CA and BBX7600 are powerful backpack blowers designed for both professional landscapers and homeowners seeking high-performance tools for yard maintenance. These models embody a combination of innovative technology, ergonomic design, and robust performance, making them ideal for tackling a range of outdoor cleanup tasks.

The BBX7600CA is equipped with a 75.6 cc, 4-stroke engine, which delivers impressive blowing power without the need for a fuel/oil mix. This engine type offers reduced emissions and a quieter operation, making it environmentally friendly and user-friendly. The BBX7600 features a similar robust engine configuration, offering reliable performance and durability to handle demanding jobs.

One of the standout features of these blowers is the “Easy Start” technology. This system significantly reduces the pull force required to start the engine, allowing for hassle-free ignition, especially during colder weather. Additionally, both models are designed with an efficient air filter system that enhances airflow while ensuring longevity and reducing the need for frequent maintenance.

Ergonomics play a critical role in the design of the BBX7600CA and BBX7600. The blowers come with a padded harness and adjustable shoulder straps, allowing users to work comfortably for extended periods. Their lightweight construction further adds to user convenience, making them easy to maneuver around the yard, whether you’re clearing leaves, debris, or grass clippings.

Another notable characteristic is the anti-vibration technology integrated into these models. This feature minimizes operator fatigue by dampening vibrations that are common in high-powered outdoor equipment. As a result, users can maintain productivity without discomfort during extensive use.

The blowers are also designed with an easy-to-access throttle and cruise control functionality. This allows users to maintain a consistent power output without having to keep their finger on the throttle trigger, enhancing control and comfort.

In summary, the Makita BBX7600CA and BBX7600 are versatile, efficient, and user-friendly backpack blowers. Their strong engines, ergonomic designs, and advanced features make them valuable additions to any outdoor tool arsenal, capable of tackling tough jobs with ease while ensuring operator comfort and reduced environmental impact. Whether for professional landscaping or residential use, these blowers stand out as reliable choices for maintaining a clean and tidy outdoor space.
Top Page Image Contents